Using The Thermostat; Thermostat Overview; User Menu; Thermostat Operation - Emerson 80 Serie Instrucciones De Instalación Y Funcionamiento

USING THE THERMOSTAT

THERMOSTAT OVERVIEW

Before you begin using your thermostat, you should be familiar with its features, display and
the location/operation of the thermostat buttons and switches.
THERMOSTAT BUTTONS
THE DISPLAY
AND SWITCHES
1.) Fan Switch 10.) Thermostat is protecting the equipment from short cycling
2.) System Switch 11.) Indicates that the system is running in cool, heat or auxiliary
3.) Backlight Button (located on the top 12.) Displays the current time
of the thermostat
4.) Set Correct Time 13.) Battery status indicator
5.) Hold a Permanent Temperature 14.) Low battery indicator
6.) Cancels Hold – Returns to 15.) Day of the week used when programming a schedule
Programmed Schedule
7.) Raises Temperature Setting 16.) Permanent hold (bypassing the schedule)
8.) Access Menu Options 17.) Temperature setpoint
9.) Lowers Temperature Setting 18.) Appears when the keypad is locked (to prevent unwanted
19.) Next (Menu button) is used to navigate within a menu
20.) Access the schedule and customize thermostat features
21.) Back (Run button) is used to navigate within a menu
22.) Exit (Hold button) returns to the home screen
23.) SEE TROUBLESHOOTING
13 14
12
1
11
2
23
10
4
Whenever " " appears in the display, new premium brand AA alkaline batteries
Replace
should be installed. If the house will be unoccupied for an extended period and either "
or " " is displayed, install new batteries before leaving.
Replace
5
(5-minute delay)
mode (The auxiliary will run in Heat mode when the heat
pump cannot maintain the set temperature.)
changes)
3
15 16 17
7
8
9
19
22 21 20
5 6

USER MENU

To customize thermostat settings, press the Menu button from the home screen. Use the
or buttons to highlight Settings and press Next. Use Next and Back to navigate
through menu items. Press
User's Menu #
(Press Menu button
and release)
01
02
03
04
05
06
07

THERMOSTAT OPERATION

Set Current Time and Day
Note: Time icons will flash at initial power up or after a reset.
1.) Press Set Time
2.) Use or
3.) Press Next to advance to set the minutes and day of the week
4.) Press Exit when finished.
The default program is 5-1-1 Day, but can be setup as a 7-Day or Non-Programmable
18
thermostat (refer to the User Menu above)
• Hold Temperature (bypassing the schedule) – With the System Switch set to Heat or
Cool, momentarily press the Hold button. Hold will be displayed. Use
temperature. The thermostat will hold the room temperature at the selected setting until
you press Run to start program operation again.
• Program Override (Temporary Hold) – Press
displayed. The thermostat will override the schedule until the next programmed time
period with a minimum override of 2 hours. Then the thermostat will automatically revert
to the program.
• Keypad Lockout – To prevent unwanted changes, the buttons can be disabled.
To turn this feature On, press and hold
" (this can also be turned on in the menu). To turn Off, press and hold
ton for 3 seconds.
or to change the setting.
Default Setting
Description
(flashing icons)
Schedule Type (set as either
7-Day, 5-1-1 Day or Non
Programmable)
Early Start (starts heating
or cooling early so your
programmed temperature is
reached by the programmed
time)
Fahrenheit or Celsius
Temperature Display Ad-
justment (adjust the Room
Temperature)
Continuous Display Light
(keep the backlight always on –
"C" wire required)
Change Air Filter (set up a
monthly reminder)
Keypad Lock (prevent unwant-
ed changes to the thermostat)
to adjust the hour
or
and the Menu button until the
Settings
(Press or )
7 – 7 Day
5 5 – 5-1-1 Day
0 – Non-Programmable
On – start early
OFF OFF – start at program
period time
°F – Fahrenheit
°F
°C – Celsius
0 -5 to +5
On – always on
OFF
OFF – momentarily
1 to 12 – reminder time
OFF (months)
OFF – no filter reminder
On – disable buttons
OFF
OFF – all buttons are active
or to adjust the
until the desired temperature is
icon appears
and the Menu but-
6