Tabla de contenido
Publicidad
Enlaces rápidos
Models/Modèles/Modelos
136-DST
336-DST
436-DST
Series/Series/Seria
Write purchased model number here
Inscrivez le numéro de modèle ici
Escriba aquí el número del modelo comprado
For easy installation of your
Delta faucet, you will need:
• To READ ALL the instructions completely
before beginning.
• To READ ALL warnings, care and
maintenance information.
Pour installer votre robinet
Delta facilement, vous devez :
• LIRE TOUTES les instructions avant
de débuter.
• LIRE TOUS les avertissements ainsi que
toutes les instructions de nettoyage et
d'entretien.
Para instalación fácil de su
llave Delta usted necesitará:
• LEER TODAS las instrucciones
completamente antes de empezar.
• LEER TODOS los avisos, cuidados e
información de mantenimiento.
SINGLE HANDLE KITCHEN FAUCET
ROBINET DE CUISINE À UNE MANETTE
LLAVE DE COCINA DE PALANCA
You may need/Articles dont vous pouvez
avoir besoin/Usted puede necesitar:
Page 1
210072 Rev. A
Publicidad
Tabla de contenido
Manuales relacionados para Delta 136-DST
Resumen de contenidos para Delta 136-DST
- Página 1 Escriba aquí el número del modelo comprado You may need/Articles dont vous pouvez avoir besoin/Usted puede necesitar: For easy installation of your Delta faucet, you will need: • To READ ALL the instructions completely before beginning. • To READ ALL warnings, care and maintenance information.
- Página 2 RP28898▲ Handle with Set Screw Manette avec Vis de Calage Manija con Tornillo de Ajuste RP152▲ Set Screw Vis de Calage Tornillo de Ajuste RP28906 Button Bouton Botón RP51502▲ Embase Casquillo RP47029 Mounting Bracket Support de montage RP51503 Soporte de Montaje Bonnet Chapeau Bonete...
- Página 3 136-DST 336-DST 336-DST 136-DST 336-DST SHUT OFF WATER SUPPLIES. Remove Insert spray hose (1) down through SHUT-OFF WATER SUPPLIES. Remove old support assembly. Continue to step 2. old faucet. Feed tubes (1) down through faucet. Feed tubes (1) down through centre hole centre hole in sink.
- Página 4 436-DST 436-DST 436-DST SHUT OFF WATER SUPPLIES. Remove old faucet. Feed tubes Mount the spray support (1) in far right hole in sink. Hand tighten nut (1) down through centre hole in sink. Secure faucet to sink using (2). Insert spray hose (3) down through support assembly. Continue mounting plate (2) and nut with wrench (3) along with locknuts (4) to step 2.
- Página 5 For Sprayer Models Only Keeping clip (1) disengaged, insert diverter hose end (2) into Pull on clip (1) until disengaged. Pull down on diverter plug (2) to diverter housing (3) until seated. Push in clip (1) until it snaps. remove. Discard diverter plug. Pull down moderately to ensure connection has been made.
-
Página 6: Conexiones Especiales
Faucet fittings (1) are 3/8” compression, with ends not to cut the tube too short. created. Delta is not responsible for tubing that is coloured red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum cut too short or cut in a way that will not allow for a ●... - Página 7 Incorrect Installation Correct method Installation Incorrecte Bonne méthode Instalación Incorrecta Método Correcto Do not install sleeve Ensure cut is straight. upside down. Custom Fit Connections - Plastic Sleeve Installation Instructions N’installez pas le Assurez-vous que 1. Identify desired length of tube (1). Leave 1”-2” of extra length to allow for easier manchon à...
- Página 8 FLUSH YOUR SYSTEM: Remove aerator (1) and turn faucet handle (2) to the full on Check all connections at arrows for leaks. Re-tighten if necessary, mixed position. Turn on hot and cold water supplies (3) and but do not overtighten. flush water lines for one minute.
- Página 9 Setting the Handle Limit Stop (Optional) scalding because it limits the amount of hot water in the mix; however, this This faucet includes an integrated handle limit stop that has two positions. handle limit stop will not always prevent scalding because it does not com- Position 1, to the left, allows full handle motion (the full range between “all pensate for incoming pressure or sudden water temperature changes.
-
Página 10: Mantenimiento
Maintenance If spray attachment does not function properly: Replace diverter and hose If faucet exhibits very low flow: assembly (5). A. Remove and clean Aerator (1), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (2). When rein- * WARNING: Failure to securely tighten bonnet nut with a wrench could stalling parts, make sure bonnet nut (4) is tightened securely with a wrench.* result in water damage. -
Página 11: Cleaning And Care
Any damage to this faucet Delta Faucet Company Delta Faucet Canada (a division of Masco Canada Limited) as a result of misuse, abuse or neglect, or any use of other than genuine Delta® replacement Product Service Technical Service Centre parts WILL VOID THE WARRANTY.