RIB VERTIGO Wi-Fi 8 Manual Del Usuario página 15

VERTIGO Wi-Fi in combination with MASTER Wi-Fi conforms to standard EN 13849-2 (2013)
and when used with a RIB electronic control panel it is a PL "c" Category 2 protection device
for protecting persons/things from collisions caused by mechanical moving parts such as
automatic gates or doors.
The obstacle is detected for the whole distance between the infrared transmitter and receiver
which constitute the VERTIGO Wi-Fi product.
VERTIGO Wi-Fi can be positioned anywhere without needing to use electrical wire.
The Wi-Fi system (made up of a VERTIGO Wi-Fi and MASTER Wi-Fi) operate at a frequency of
868,3 MHz.
The MASTER Wi-Fi board communicates constantly with VERTIGO Wi-Fi and always indicates
interruptions of the infrared signal between the TX transmitter and the RX receiver or any type
of malfunctioning.
Each VERTIGO Wi-Fi has its own internal ID code that distinguishes it from the other devices.
The Wi-Fi system is an active security system because it constantly verifies proper functioning
of the VERTIGO Wi-Fi devices and battery condition.
When using RIB electronic control panels you can run auto-tests on the system.
With RIB actuators, RIB electronic control panels having the auto-test function and RIB safety
devices you can create an installation that conforms to the European Directives and Norms in
force.
After completing the system, you must make sure it conforms to standard EN 13241:2016.
RIB shall not be liable for any damages caused by improper, incorrect or unreasonable use of
the product.
REFERENCE TO STANDARDS FOR AUTOMATIC GATES AND DOORS
RIB MAY NOT BE HELD RESPONSIBLE FOR DAMAGES CAUSED BY IMPROPER, WRONG OR
UNREASONABLE USE.
Usage restrictions: The VERTIGO Wi-Fi photocells cannot be used on devices excluded by the
application of the EN 12978, such as:
- Protection devices for the installation on doors used for a different purpose to those ones
used for pedestrian or veheicle access, covered by the norm which principal intent is that of
allowing a safe access to industrial, commercial, public and commercial sites. Some examples
of excluded accesses can be: sluice gates, dams, lift doors, vehicles' doors, doors used mainly
to restrain animals, theatre curtains, railways barriers, barriers used only for vehicles.
- Devices used only fo the standard control and for the stopping, including the emergency
stopping, of motorized doors.
- Safety systems and safety devices used on machineries different from doors.
ATTENTION: Any possible modification of the device, or of the configuration of the same cannot
be carried out without the clear authorization by the manufacturer or, by the local authorized
dealer.
The installer of the safety device must make sure that the end user know the following:
- That the safety devices must be made known to all appropriate people.
- That the passages to reach the devices must be kept clear from any obtsacle.
- About the procedures for cleaning so to avoid the dangerous building up of material.
- The possible details for a restart of the system after an emergency or accidental stop caused
by the control system.
Any modification of the project or, of the configuration of the device, without discussing it
first with the manufacturer or with the local autorized dealer can cause dangerous situations.
VERTIGO Wi-Fi PHOTOCELLS ARE ONLY ON DURING DOOR OPERATION. THANKS TO THE SLEEP MODE.
WHEN THE DOOR IS NOT MOVING THE PHOTOCELLS ARE OFF TO ALLOW FOR LONGER BATTERY LIFE.
VERTIGO Wi-Fi are produced in wall-type versions:
- VERTIGO Wi-Fi 8 code ACG8042
- VERTIGO Wi-Fi 10 code ACG8043
to be fasten to the primary and/or secondary borders (mobile or fixed) made of iron or other
smooth material.
It is possibile, if necesary, to rotate by 90° in 90° the infrared ray direction (see picture here
aside).
APPLICATION
VERTIGO Wi-Fi 8
VERTIGO Wi-Fi 10
MOUNTING
VERY IMPORTANT!
When using a NOT RIB control panel, this
one must be complying with the reaction
time (inversion) requested by the Norm
EN 12453 (requirements of safety devices
used on motorized gates/doors).
PLACE THE VERTIGO RECEIVER ON THE TOP
OF THE LEAF AND THE COLUMNS OF THE GATE
AND IN FULL VIEW OF THE MASTER Wi-Fi.
VERTIGO TRANSMITTER MUST BE APPLIED TO
THE BOTTOM OF THE LEAF AND THE COLUMNS
OF THE GATE.
NO OBSTACLES SUCH AS WALLS, PILLARS
OR METAL CABINETS MUST BE PRESENT
BETWEEN THE RECEIVER OF THE VERTIGO
Wi-Fi PHOTOCELLS AND THE MASTER Wi-Fi.
If it is not possible to avoid that because
the obstacles cannot be removed,
please install an 868 MHz aerial (code
ACG5451) on the MASTER Wi-Fi and place
it so to guarantee a good quality radio
communication between the parts.
This solution also prevents the quick
discharge of the batteries on the VERTIGO
Wi-Fi.
* Before fastening the base of the RECEIVER to
the upper part of the leaf, check for possible
obstructions due to potential stops and/or
conveying systems.
** Space available for possible mechanical
stopper.
15
MAX DISPLACEMENT
MAX GATE WEIGHT
SPEED
150 kg 13 m/min.
300 kg 10 m/min.
500 kg 13 m/min.
1000 kg 10 m/min.
RX
TX
Measurements in mm
G
B