Master BLAST Manual De Usuario página 4

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

03. HOW TO MEMORIZE-DELETE BLAST/VEGA IN A RECEIVER
01. With a transmitter already memorized, brings the motor that you want to program in an intermediate position.
02. Press PROG of this transmitter for 5 seconds. The motor performs 2 upward movements.
03. Within 15 seconds, press P1 of BLAST / VEGA.
04. 1 upward movement: device stored!!
1 downward movement: device deleted!!
2 downward movements: error!! (*)
(*) "error" is reported if the radio code is not received in time, if the receiver's memory is full, if you try to
store in the receiver a not compatible devices
WARNING:
some motor/receiver can have a different procedure from the one described above. In this case follow the section "Memorization/cancellation of the radio device" on the user manual
of the motor/receiver.
WARNING:
to verify that the sensor is properly memorized, bring the tuned receivers in an intermediate position, rotate rapidly the cups of the anemometer to simulate the condition of "wind
alarm". The tuned receivers have to move upward and the manual controls must be inhibited. To exit the condition of "wind alarm", press any button of the sensor until the LEDs light
up briefly, then release the button.
WARNING:
if the receiver remains without power supply, at power up the sensor and the receiving device can take up to 10 minutes to re-establish communication radio.
04. WIND FUNCTION
If the wind speed is above the set threshold for at least 3 seconds, an upward movement is commanded to protect the awning (wind alarm). During this phase all manual commands
are disabled. The device exits from the "wind alarm" if the wind speed keeps below the set threshold for at least 8 minutes. The wind threshold is varying from 5 km/h to 35 km/h. The
factory sets the wind threshold at 15 Km/h. To modify the threshold:
01. Press P1 for about 3 seconds until the LED 1 starts flashing.
02. LED1 indicates the threshold.
Example: 1 flash - pause - 5 flashes = 15 Km/h
03. Use P1 and P3 to set the new threshold.
Example: 15 Km/h = press 1 time P1 e 5 times P3
04. Wait 10 seconds. LED1 indicates the new threshold.
05. VISUAL SIGNALS
Led WIND
Led MANOEUVRE
Button P1
Button P3
Led SUN
Button P2
06. SUN FUNCTION (VEGA only)
An automatic downward manoeuvre is performed if the intensity of the sun is above the set threshold for at least 2.5 minutes. An automatic upward manoeuvre is performed when the
intensity of the sun returns to less then the set threshold for at least 18 minutes. Once performed an automatic downward manoeuvre for the presence of sun, the subsequent
automatic operation performed by the sensor will be an upward manoeuvre for to the absence of sun and so on. The user can operate the awning, but the manual control doesn't
affects the operating logic of the sun sensor. The sun threshold is variable from 1 to 45 Klux. The factory sets the threshold to 16 Klux.
To modify the sun threshold:
01. Press P2 for about 3 seconds until the LED 2 starts flashing.
02. LED2 indicates the threshold.
Example: 1 flash - pause - 5 flashes = 15 Klux
03. Use P1 and P3 to set the new threshold.
Example: 15 Klux = press 1 time P1 e 5 times P3
04. Wait 10 seconds. LED 2 indicates the new threshold.
07. RESET
This procedure restores the factory settings
of the device. This procedure must be
carried out by qualified technical personnel.
Once the "reset" is performed, the
technician must install this device again and
verify proper operation. With this procedure
the sensor IS NOT DELETED FROM THE
MEMORY OF THE RECEIVERS.
All products and technical characteristics on this document are subjects to variations without any notice. Except for concessions and specific case agreed in advance with the manufacturer, the device must be used
only with receiving devices of the same manufacturer. The manufacturer cannot be consider responsible for damage caused by improper, incorrect or unreasonable uses.
Example: 2 flashes - pause - 1 long flash = 20 Km/h
Example: 20 Km/h = press 2 times P1 (e 0 volte P3)
BLAST
LED WIND
off: wind below threshold
red: wind above threshold
LED SUN
red: wind alarm
LED MANOEUVRE
quickly flashing: wind alarm
Example: 2 flashes - pause - 1 long flash = 20 Klux
Example: 20 Klux = press 2 times P1 (e 0 volte P3)
01. Press together P1 and P3. After a few seconds the three LEDs start flashing.
02. Hold P1 and P3 for around 30 sec, until the three LEDs light on.
03. Release the buttons: the three LEDs light off.
RESET COMPLETED!!
R
All rights reserved.
Example: 5 flashes = 5 Km/h
Example: 05 Km/h = press (0 time P1 e) 5 times P3
VEGA
LED WIND
off: wind below threshold
red: wind above threshold
LED SUN
off: sun below threshold
green: sun above threshold
LED MANOEUVRE
off: last executed automatic manoeuvre: «up»
green: last executed automatic manoeuvre: «down»
slowly flashing: the sensor is just turned on or just straight out of «wind alarm»
quickly flashing: wind alarm
Example: 5 flashes = 5 Klux
Example: 05 Klux = press (0 time P1 e) 5 times P3
02
P1
PROG
(5 seconds)
red: wind alarm
30
P1
P3
seconds
P1
P2
RESET
COMPLETED

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Vega

Tabla de contenido