Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
H-2708, H-2900, H-3045
H-5387, H-6710, H-7504
H-8921
INDUSTRIAL
PALLET TRUCK
MODEL
Capacity
Max. Fork Height
Min. Fork Height
Fork Length
Overall Fork Width
Fork Wheel Diameter
Steering Wheel Diameter
Net Weight
WARNING! Operator must read and understand
instructions here and on truck prior to use.
On the handle of the pallet truck, you will find the
control lever, which can be set in three positions.
(See Figure 1)
Figure 1
- LOWER = to lower the forks
- NEUTRAL = to move the load
- RAISE = to raise the forks
PAGE 1 OF 9
1-800-295-5510
uline.com
TECHNICAL DATA
H-2708/H-2900/H-3045/H-5387/H-7504
5,500 lbs.
7.5"
3.0"
48"
27"
3" Polyurethane
7" Polyurethane
165 lbs.
OPERATION
H-6710
5,500 lbs.
7.5"
3.0"
48"
21"
3" Polyurethane
7" Polyurethane
152 lbs.
1.
If the forks elevate while pumping in the NEUTRAL
position, turn the setting screw clockwise until
pumping the handle does not raise the forks and the
NEUTRAL position functions correctly.
2. If the forks descend while pumping in the NEUTRAL
position, turn the setting screw counterclockwise until
the forks do not lower.
3. If the forks do not descend when the control lever is in
the LOWER position, turn the setting screw clockwise
until raising the control lever lowers the forks. Then
check the NEUTRAL position as per step 1 and 2.
4. If the forks do not lift while pumping in the RAISE
position, turn the setting screw counterclockwise
until the forks elevate while pumping in the RAISED
position. Then check the NEUTRAL and LOWER
position as per steps 1, 2 and 3.
NOTE: When viewing the truck from the handle
side, the setting screw is located on the right
side of the pump above the right wheel. The
truck will lower faster or slower depending on
how far in or out the screw is adjusted.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
H-8921
5,500 lbs.
7.5"
3.0"
72"
27"
3" Polyurethane
7" Polyurethane
258 lbs.
1020 IH-2708
Publicidad
Tabla de contenido
Manuales relacionados para Uline H-2708
Resumen de contenidos para Uline H-2708
- Página 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. H-2708, H-2900, H-3045 H-5387, H-6710, H-7504 1-800-295-5510 H-8921 uline.com INDUSTRIAL PALLET TRUCK TECHNICAL DATA MODEL H-2708/H-2900/H-3045/H-5387/H-7504 H-6710 H-8921 Capacity 5,500 lbs. 5,500 lbs. 5,500 lbs. Max. Fork Height 7.5"...
- Página 2 MAINTENANCE DAILY CHECK AND MAINTENANCE Check the oil level every six months. The oil capacity is Daily checks of the pallet truck can limit wear and tear about 0.3L. Restore the fluid level in the reservoir to 5mm on the unit. Pay special attention to the wheels, axles, handle, forks and lift and lower controls.
- Página 3 The setting screw is not in the correct position. Adjust the setting screw. (See Operation) NOTE: Do not attempt to repair the pallet truck unless you are trained and authorized to do so. 1-800-295-5510 uline.com PAGE 3 OF 9 1020 IH-2708...
-
Página 4: Datos Técnicos
H-2708, H-2900, H-3045 H-5387, H-6710, H-7504 800-295-5510 H-8921 uline.mx PATÍN HIDRÁULICO INDUSTRIAL DATOS TÉCNICOS MODELO H-2708/H-2900/H-3045/H-5387/H-7504 H-6710 H-8921 Capacidad 2,495 kg (5,500 lbs.) 2,495 kg (5,500 lbs.) 2,495 kg (5,500 lbs.) Altura Máx. de Horquilla 19 cm (7.5") 19 cm (7.5") 19 cm (7.5") -
Página 5: Mantenimiento
MANTENIMIENTO ACEITE REVISIÓN DIARIA Y MANTENIMIENTO Revise el nivel de aceite cada seis meses. La capacidad La revisión diaria del patín hidráulico puede reducir el de aceite es aproximadamente 0.3L. Restaure el nivel desgaste de la unidad. Preste atención especialmente del líquido en el depósito a 5mm abajo del borde;... -
Página 6: Solución De Problemas
Reajuste el tornillo de ajuste. El tornillo de ajuste no está en la posición correcta. (Vea Funcionamiento) NOTA: No intente reparar el patín hidráulico a menos de que haya sido entrenado o autorizado. 800-295-5510 uline.mx PAGE 6 OF 9 1020 IH-2708... -
Página 7: Données Techniques
H-2708, H-2900, H-3045 H-5387, H-6710, H-7504 1-800-295-5510 H-8921 uline.ca TRANSPALETTE INDUSTRIEL DONNÉES TECHNIQUES MODÈLE H-2708/H-2900/H-3045/H-5387/H-7504 H-6710 H-8921 Capacité 2 494,8 kg (5 500 lb) 2 495 kg (5 500 lb) 2 495 kg (5 500 lb) Hauteur max. des fourches 19,1 cm (7,5 po) 19 cm (7,5 po) 19 cm (7,5 po) Hauteur min. des fourches 7,6 cm (3 po) 8 cm (3 po) -
Página 8: Lubrification
ENTRETIEN HUILE VÉRIFICATION ET ENTRETIEN QUOTIDIENS Vérifiez le niveau d'huile tous les six mois. Le volume La vérification quotidienne du transpalette peut en maximal d'huile est d'environ 0,3 litre. Rétablir le niveau limiter l'usure. Portez une attention spéciale aux roues, aux essieux, à la poignée, aux fourches et aux leviers de de fluide dans le réservoir à... -
Página 9: Dépannage
La vis de réglage n'est pas à la position appropriée. Réglez la vis de réglage. (Voir Fonctionnement) REMARQUE : Ne tentez pas de réparer le transpalette à moins d’être formé ou autorisé pour le faire. 1-800-295-5510 uline.ca PAGE 9 OF 9 1020 IH-2708...