JUNO T595 Instrucciones De Instalación

Feed/Suspension Cable Kits Models T595/T596/TU596(T-Bar Ceiling)
WARNING: Read and save all instructions before installing. Do not install the Trac in damp or wet locations. Do not attempt to energize
anything other than a Trac light fixture. Do not install any fixture assembly closer than 6 inches from any curtain or similar combustible
materials. Use only fixtures and fittings intended for use with compatible Juno Trac systems. Reference local electrical/engineering
codes for approved wiring techniques/requirements.
NOTE: The total number of cable suspension kits per section of Trac must be as follows: 2-foot, 4-foot and 6-foot require 2 cable
suspension kits, 8-foot section requires 3 cable suspension kits. Additional Trac lengths require cable suspension kits every 4-feet.
SAVE THESE INSTRUCTIONS
Juno Feed/Suspension Cable Kits are
compatible with Juno Trac-Master
Trac-Lites™ Trac systems
T596/TU596 FEED/SUSPENSION
CABLE KIT
Step 1. Make sure that the power is off.
Step 2. Determine where the Feed/Suspension
kit will be installed on the ceiling, and mark the
the desired location on the T-Bar.
Step 3. Remove knockout on mounting plate and
attach mounting plate to T-Bar by rotating until
clip locks onto T-Bar.
Step 4. Use the mounting plate as a template
and cut a hole in the ceiling tile where the knock-
out hole in the mounting plate is located.
Step 5. Secure BX to mounting plate and make
electrical connections in accordance with Local
and National Electrical Codes.
Step 6. Screw on canopy attachment stud to
mounting plate. Align center hole in canopy with
canopy attachment stud and secure canopy to
mounting plate with cable coupler.
Step 7. Canopy is supplied with the power cord
factory installed in canopy. If power cord needs to
be shortened it must be shortened at Trac side.
T-Bar
T-Bar
Clip
Canopy
Attachment
Stud
Cable Coupler
Cable
1300 South Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • Visit us at www.junolightinggroup.com
INSTALLATION INSTRUCTIONS
Mini-Canopy Assembly
T595 CABLE SUSPENSION KIT
® and
Step 1.
Determine where
the suspension
Sliding Bracket kit will be installed
Assembly (For use
on the T-Bar, and
with Trac-Master only)
mark the desired
location.
Trac Locking Screw
Step 2. Attach Mini-Canopy Assembly to T-Bar by
Screw
rotating until clip locks onto T-Bar.
Step 3. Determine where the next suspension
cable will be installed and repeat Step 1 and
Step 2.
CONNECTING T595/T596/TU596
TO TRAC SYSTEM
Trac-Lites Trac
System
Cable
Coupler
Wave
Mini-Canopy Assembly
Washer
BX or
Power
Armored
Cord
Cable
Mounting Plate
Screw Screw
Knockout
End
Feed
Sliding Bracket
Assembly (For use
with Trac-Master only)
Canopy
Trac Locking Screw
Cord Strain
NOTE: Make sure the power supply cable is
Relief
not shorter than the support cable.
Power Cord
Cable
Coupler
T-Bar Ceiling Cable T-Bar Ceiling Cable
Suspension Kit Suspension Kit
(for 15/16" flush mount only) (for 15/16" flush mount only)
Mini-Canopy Assembly
T-Bar T-Bar
T-Bar Ceiling Cable
Clip Clip
Suspension Kit
(for 15/16" flush mount only)
Cable Cable
Mini-Canopy Assembly
Sliding Bracket
Assembly (For use
Plunger
with Trac-Master only)
Cable
Gripper
Sliding Bracket,
Trac Locking Screw
(Attaches to Trac)
Screw Wave Washer
Sliding Bracket
Assembly (For use
with Trac-Master only)
Trac Locking Screw
Screw
Trac-Master Trac
System
Cable
Coupler
T-Bar Ceiling Cable
Suspension Kit
(for 15/16" flush mount only)
Wave
Cable
Washer
Coupler
T-Bar Power
Power
Clip
Cord
Cable
Concealed Concealed
Wireway Wireway
Wave
End End
Washer
Feed Feed
Power
Cord
Plunger
Gripper
Sliding Bracket,
Screw
(Attaches to Trac)
Screw Wave Washer
End
Feed
© 2014 Juno Lighting, LLC.
T-Bar Ceiling Cable
Suspension Kit
(for 15/16" flush mount only)
Mini-Canopy Assembly
T-Bar
T-Bar
Sliding Bracket
Clip
Assembly (For use
with Trac-Master only)
Trac Locking Screw
Screw
Installation for Trac-Master Trac
Canopy system Canopy
Attachment Attachment
Stud Step 1. Install the sliding bracket assembly by Stud
T-Bar
guiding it through the concealed wireway.
Clip
Step 2. At desired position, secure with screw.
Plunger
Cable Coupler Cable Coupler
Gripper
Installation for Trac-Lites Trac system
Cable
Sliding Bracket,
(Attaches to Trac)
Step 1. Locate existing holes on Trac.
Wave Washer
Cable
Step 2. Unscrew bracket from Gripper and
Coupler
discard. Retain screw and wave washer. Secure
the Gripper to top of Trac with screw and wave
washer.
Plunger
Gripper
ATTACHING CABLE TO TRAC
Sliding Bracket,
(Attaches to Trac)
Step 1. Adjustments in lengths can be made
Wave Washer
simply by cutting cables to desired length.
Wave
Washer
Step 2. Feed cable through the Gripper until it
Cable Cable stops. Continue until all cables are attached to
Power
Coupler Coupler
Trac. To release cable from Gripper, see "How
Cord
Gripper Works" in next column.
ATTACHING FEED TO TRAC
Screw
T-Bar
Step 1. Attach electrical/power cord to end feed
End
of Trac. Refer to instructions that came with your
Feed
specific end feed. Note: If you wish to secure the
Cable
power cord to the suspension cable, cable ties
T-Bar
Coupler
are included.
Clip
Power
Cord Cord Step 2. Turn power on, install fixtures.
HOW GRIPPER WORKS
The gripper is a unique, self-
locking suspension device.
Canopy
The gripping mechanism is
Attachment
End
Feed spring loaded and allows the Stud
Power
gripper to unlock so that the
Cord
cable length can be changed.
Cable Coupler
Step 1. Insert cable through
gripper mechanism.
Concealed
Step 2. To adjust, depress
Wireway
the plunger with fingertip
End
and pull cable to release.
Feed
Release the plunger to
lock cable into position.
Printed in U.S.A.
Cable
Coupler
T-Bar
Clip
Cable
BX or BX or
Armored Armored
T-Bar
Cable Cable
Mounting Plate Mounting Plate
T-Bar
Clip
Knockout Knockout
Plunger
Gripper
Sliding Bracket,
(Attaches to Trac)
T-Bar
Wave Washer
Canopy Canopy
T-Bar
Clip
Cord Strain Cord Strain
Relief Relief
Power Cord Power Cord
Cable
Canopy
Attachment
Cable
Stud
Coupler
Cable Coupler
Cable
Power
Cord
Concealed BX or
Wireway Armored
Cable
End
Feed
Mounting Plate
Knockout
Canopy
Cord Strain
Relief
Power Cord
Cable
P3666
Rev 9/14
Canop
Attach
Stud
Ca
BX or
Armore
Cable
Mounting
Knock
Canop
Cord Strai
Relief
Power Cor