Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Before using your kettle
If you are using the kettle for the first time, it is
recommended that you should clean your kettle before
use by boiling the Max capacity of water once and then
discarding the water. Wipe the surface with damp cloth.
NOTE:
The max capacity of kettle is 2.0L.
Using your water kettle
1. Place the unit on the level surface.
2. To fill the kettle, remove it from the power base and
open the lid by pressing the lid release button, fill with
the desired amount of water, and then close the lid.
Alternatively, the kettle may be filled through the spout.
The water level should not exceed MAX marks or sit
below MIN level. Too little water will cause the kettle
switching off before the water has boiled.
NOTE:
Do not fill the water over the maximum level, as
water may spill out of the spout when boiling. Ensure
that the lid is firmly in place before plugging the power
outlet.
3. Position the kettle on the power base.
4. Connect the plug into a power outlet. Press down
the On/Off switch, the indicator will light up. Then the
kettle will start to boil the water, once the water has
being boiled the On/Off switch will be off automatically.
You can shut off the power by lifting the On/Off switch
at any moment during boiling water. If you want to boil
water again, only press down the On/Off switch directly
to restart the kettle.
NOTE:
Ensure that the On/Off switch is free of
obstructions and the lid is firmly closed, the kettle will
not turn off if the switch is constrained or if the lid is
opening.
5. Lift the kettle from the power base and then pour the
water.
NOTE:
Operate carefully when pouring the water from
your kettle as boiling water may result in scald, besides,
don't open the lid while the water in the kettle is hot.
6. The kettle will not re-boil until the On/Off switch is
pressed down again. The kettle may be stored on the
power base when not in use.
NOTE: Always disconnect the power supply when not
use.
Boil-dry protection
Should you accidentally let the kettle operate without
water, the boil-dry protection will automatically switch
off the power. If this occurs, allow the kettle to cool
before filling with cold water to reboil.
Cleaning and maintenance
Always disconnect the appliance from the power outlet
and cool it down completely before cleaning.
1. Never immerse the kettle, power cord or power base
in water, or allow moisture to contact with these parts.
2. Wipe the appearance of body with a damp cloth or
cleaner, never use a poisonous cleaner.
3. Remember to clean the filter at intervals. For easier
cleaning, detach the filter and then replace it after
cleaning.
CAUTION:
Do not use chemical, steel, wooden or
abrasive cleaners to clean the outside of the kettle to
prevent the gloss loss.
4. When not in use, the power cord can be stored at the
bottom of the appliance.
5. When not use or storage, the power cord may be
wound under the bottom of kettle.
Removal of mineral deposits
Your kettle should be periodically descaled as the
mineral deposits in tap water may form scale at the
bottom of kettle interior so as to cause the operation
less efficiency. You can use the commercially available
descaler and follow the instructions on the package
of descaler. Alternatively, you may follow the below
instructions to use the white vinegar.
1. Fill the kettle with 3 cups of white vinegar, then adding
water to the amount so as to cover the bottom of kettle
completely. Leave the solution in the kettle overnight.
2. Then discard the mixture in the kettle, then filling the
kettle with clean water, boiling and then discard the
water. Repeat several times until the odor of vinegar has
been flushed away. Any stains remaining inside the spout
can be removed by rubbing with a damp cloth.
Environment friendly disposal
You can help protect the environment!
Please remember to respect the local regulations:
hand in the non-working electrical equipments to an
appropriate waste disposal center.
Publicidad
Tabla de contenido
