Starting The Appliance - nardi LSI45HL.A000 Manual Del Usuario

Starting the Appliance

Starting a wash cycle...
After having completed all of the installation steps in the preced-
ing paragraphs, turn on the water to the unit, partially open the
door of the dishwasher, and press the ON-OFF button "C" lo-
cated on the control panel. The "D" indicator light will come on.
At this point, the appliance is on and ready to be programmed.
Setting and Starting a wash Cycle
Choose the desired cycle by pressing the cycle selection button
"E". Each time it is pressed, one of the cycle indicator lights "A"
will come on in succession.
Choose the wash cycle you feel is most appropriate for the type
of dishes that need washing (consult the wash cycle table con-
tained in this manual, especially when first using the appliance).
Close the door and press the "E" programming button, a short
acoustic signal will sound indicating that the wash cycle has be-
gun and cannot be modified. If necessary, read the paragraph
entitled, "Cancelling or modifying a cycle while underway. "The
end of the cycle will be signalled by a double acoustic sound,
and the indicator light "A" will begin to blink.
Memory Function Module
If the dishwasher is switched off through the ON/OFF button, or
the power is cut suddenly while the selected washing program is
active, the program is not cancelled. The controls use a micro-
processor device, to memorize the information about the selected
washing program. Once the machine is again powered on, the
dishwasher will be resumed from the point it was interrupted.
Cancelling or modifying a cycle while underway...
Canceling or modifying a washing program cycle
1:To modify or cancel the carrying out of a washing cycle (being
the door opened), it's necessary to reset the previous
programming, by holding pushed the programme selector but-
ton "E" for at least 3 seconds, and the buzzer emits one short
warning signal.
2:If the reset operation was successful, a drain phase is started.
Once the drain phase is ended, the dishwasher stands waiting
for a new programming.
Premise: A cycle that is underway can only be modified if it has
only been running for a short time.
Otherwise, the detergent may have already been used, and the
appliance may have already drained the wash water. In this case,
the detergent dispenser must be refilled (see the paragraph
entitled, "Loading the Detergent").
If you forget to load some of the dishes...
The wash cycle can be interrupted by opening the door carefully
(in order to avoid being sprayed by hot water). When the door is
closed again, the cycle will automatically restart at the point where
it left off.
At the end of the wash cycle...
The end of the cycle will be indicated by a double acoustical
signal and the blinking of the "A" indicator light. Open the door,
turn off the appliance using the ON/OFF switch and turn off the
water supply to the unit. Wait a few minutes before removing the
dishes so as to avoid handling them while still hot (when they
are more susceptible to breakage) and to get better drying results.
Setting The Start Delay Time
Open the door of the dishwasher partially. If the "I" button is
pressed (see, Close-up View" Control Panel"). The start time for
the wash cycle can be delayed for 2,4 or 6 hours.
Each time the button is pressed, the "H" light will come on indi-
cating the length of the delay.
After selecting the delay time, the wash cycle can be set, as
explained in "Starting a wash cycle..." There will be a short acous-
tic signal, and at this point the delay period will begin to count
down. During this period the delay indicator light (H) will blink. At
the end of the delay time, the indicator will stop blinking and the
cycle will start.
NOTE:
If the power to the appliance goes off or the door is opened dur-
ing the delay period, the clock will stop the countdown. It will
start again when the power has come back on, or when the door
has been closed.
Wash Cycle Adjustment Buttons
1/2 Load Button
This button (see" Close-up View-Control Panel", letter "B") makes
it possible to wash dishes using only the upper rack if there are
not enough dishes for a full load, This will allow you to save on
water and electrical energy.
It cannot be used with the heavy duty wash cycles.
.61.
GB