Troubleshooting Guide; Technical Service - Desa ELECTRIPAK 5312 Manual De Instrucciones

SYMPTOM POSSIBLE CAUSE
Lights will not come 1. Light switch is turned off.
on. 2. F l o o d l i g h t i s l o o s e o r
burned out.
3. Fuse is blown or circuit breaker
is turned off.
4. Daylight turn-off is in effect (re-
check after dark).
5. Incorrect circuit wiring, if this is a
new installation.
6. Re-aim the sensor to cover de-
sired area.
Lights come on 1. Light Control may be installed in
in daylight. a relatively dark location.
2. Light Control is in Test.
(Set control switch to an
ON-TIME position).
Lights come on 1. Light Control may be sensing
for no apparent small animals or automobile traf-
reason. fi c (re-aim sensor).
2. R a n g e i s s e t t o o h i g h .
(Reduce Range).
3. 2-L
Lights turn off too 1. Sensor is in a relatively dark loca-
late in Dusk-to- tion. (Relocate sensor, or use 3
Dawn setting hr or 6 hr setting.)
Please call 1-800-858-8501 for assistance before returning product to store.
If you experience a problem, follow this guide. You may also want to visit our Web site at: www.desatech.com. If the
problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:
DESA Specialty Products
P.O. Box 90004, Bowling Green, KY 42102-9004
* If contacting Technical Service, please have the following information available: Model Number, Date of Pur-
chase, and Place of Purchase.
This is a "Limited Warranty" which gives you specifi c legal rights. You may also have other rights which vary from state to state or province
to province.
For a period of 90 days from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected
at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other expend-
able items are not covered by this warranty. Unauthorized service or modifi cation of the product or of any furnished component will
void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use,
unauthorized service, or return shipping charges.
This warranty covers only DESA Specialty Products assembled products and is not extended to other equipment and components that
a customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY,
REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PUR-
POSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON
THE PART OF DESA SPECIALTY PRODUCTS FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states
or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. Proof of purchase is required for warranty claims.
All manuals and user guides at all-guides.com

TROUBLESHOOTING GUIDE

Lighting Timer is on.
EVEL

TECHNICAL SERVICE

No Service Parts Available for this Product
90 DAY LIMITED WARRANTY
SYMPTOM POSSIBLE CAUSE
Lights stay on 1. A fl ood lamp is positioned too close to
continuously. the sensor or pointed at nearby objects
that cause heat to trigger the sensor.
(Reposition the lamp away from the
sensor or nearby objects).
2. Light Control is pointed toward a heat
source like an air vent, dryer vent, or
brightly-painted heat-refl ective surface.
(Reposition sensor. Reduce Range).
3. Light Control is in Manual Mode.
(Switch to Auto.)
Lights fl ash on 1. Heat or light from the lamps may be
and off. turning the Light Control on and off.
(Reposition the lamps away from the
sensor).
2. Heat being refl ected from other objects
may be affecting the sensor. (Reposi-
tion sensor).
3. Light Control is in the Test mode and
warming up. (Flashing is normal under
these conditions. Turn Boost off.)
4. Light may be leaking through the fl ood-
lamp refl ectors. (Replace the lamps
with new high quality PAR 38 lamps
or on Model SL-5318, make sure the
metal lamp protectors are installed).
Lights flash 1. Sensor is detecting its own lights.
once, then stay (Reposition lamps to keep area below
off in Manual the sensor relatively dark.)
Mode.
4 598-1274-00