Control Leds - Genius JA277K Instrucciones Para El Uso - Normas Para La Instalacion

ENGLISH
5.2 STOP
Terminals "11-12" (Circuit Normally Closed). The status of this input is signalled by LED 1. This circuit is connected to any device
(e.g. button, pressure switch) which, when a contact is opened, can stop the gate motion.
Note: If STOP devices are not connected, jumper connect the input. To install multiple STOP devices, connect the NC
contacts in series.
5.3 PULSE A - TOTAL OPENING
Terminals "11-13". (Circuit Normally Open). The status of this input is signalled by LED 2. This circuit is connected to any device
(e.g. button, radio control, etc.) which, when a contact is closed, generates a gate opening and/or closing pulse.
Note: To install multiple pulse devices connect the contacts in parallel.
5.4 PULSE B - PARTIAL OPENING
Terminals "11-14". (Circuit Normally Open). The status of this input is signalled by LED 3. This circuit is connected to any device
(e.g. button, radio control, etc.) which, when a contact is closed, generates a gate opening and/or closing pulse. The
opening time has a fixed lenght of 10 seconds.
Note: To install multiple pulse devices connect the contacts in parallel.
5.5 CLOSING PROTECTION PHOTOCELLS
Terminals "15-16" (Circuit Normally Closed). The status of this input is signalled by LED 4. This circuit is connected to any safety
device (photocells, pressure switch, detector, etc.) which, when a contact is opened, acts as a safety on the closing motion.
The effect will vary depending on the settings performed using dip-sw 4.
Note: To install multiple safety devices connect the NC contacts in series.
Note: If safety devices are not connected, jump connect the input.
It is possible to prevent the gate from closing by connecting a 24h timer in series to the closing photocell circuit.
6. TERMINAL BOARD M4 (LOW VOLTAGE) CONNECTIONS - DESCRIPTION
6.1 OPENING LIMIT SWITCH
Terminals "17-18" (Circuit Normally Closed). The status of this input is signalled by LED 5. This circuit is connected to the
opening limit switch.
6.2 CLOSING LIMIT SWITCH
Terminals "18-19" (Circuit Normally Closed). The status of this input is signalled by LED 6. This circuit is connected to the closing
limit switch.
6.3 ACCESSORY POWER SUPPLY
Terminals "20-21". (24 V~). Warning: the max. load for the accessories is 500 mA.
6.4 ANTENNA
Terminals "22-23". Antenna input. This should not be used if the receiver already has its own antenna input
The unit is designed to house a single or two-channel radio-receiver module. To install the module, cut off the electric power
supply and insert the module into the special connector M5 inside the unit.
When a two-channel radio-receiver module is inserted into connector M5, it is possible, using jumpers JP1-JP2, to activate
or deactivate the second channel on pulse B (partial opening): jumpers enabled = second channel activated; jumpers
disabled = second channel not activated.
LEDS
1 - Stop
2 - Pulse A
3 - Pulse B
4 - Photocells
5 - Opening limit switch
6 - Closing limit switch
Note: Bold is used to indicate the led condition with the gate at rest.
10.1 ELECTRONIC CLUTCH
To adjust the anti-crushing system tripping threshold use trimmer "A". To reduce the torque, turn the trimmer counterclockwise.
To increase the torque, turn the trimmer clockwise. It is recommend to calibrate this torque to meet current standards.
10.2 PAUSE
To adjust the pause duration (for automatic operation), use trimmer "B". The duration can be adjusted from 0 to120 seconds.
10.3 OPEN/CLOSE
To adjust the duration of the gate opening/closing time, use trimmer "C". The duration can be adjusted from 10 to 120
seconds. Note: To obtain maximum system efficiency, adjust the opening/closing time so that the electric motor can be fed
for a few seconds after the gate has reached the limit switch.
7. INSERTING THE REMOTE CONTROL RECEIVER BOARD
8. TWO-CHANNEL SELECTION JUMPER

9. CONTROL LEDS

ON
Control deactivated
Control activated
Control activated
Safety devices disabled
Limit switch free
Limit switch free
10. ADJUSTMENTS WITH TRIMMER
OFF
Control activated
Control deactivated
Control deactivated
Safety devices enabled
Limit switch occupied
Limit switch occupied
6
LED 7 Diagnostic
Slow: Correct operation
Fast: Electronic clutch circuit malfunction
or incorrect motor connection