Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Wayne Dalton, a division of Overhead Door
Corporation
P.O. Box 67, Mt. Hope, OH 44660
www.Wayne-Dalton.com
NOTE: Use these installation instructions in conjunction with the main Installation Instructions and Owner's Manual. This kit can only be used with
Wayne-Dalton 8000 and 9100 doors 7'-0" high, 8'-0" and 9'-0" wide.
NOTE: Do not permanently attach weather seal to the jamb at this time.
Permanent installation will be done after door installation is completed.
Cut three (3) pieces of weather seal for the jambs and header.
For quick install track: Align the weather seals with the inside edge of the
opening. Temporarily nail the weather seal to the jamb to keep the bottom
section from falling out of the opening during installation. Equally space nails
approximately 12" to 18" apart.
For fully adjustable track: Align the edge of the weather seals an 1/8"
to 1/4" inside the edge of the opening. Temporarily nail the weather seal to
the jamb to keep the bottom section from falling out of the opening during
installation. Equally space nails approximately 12" to 18" apart.
After door installation is complete, adjust weather seal (if necessary).
Permanently attach the weather seal to both door jambs and header. Avoid
pushing weather seal too tightly against face of door.
NOTE: For door section identification, refer to the main Installation
Instructions and Owner's manual.
Place the 3" u-bar over the top rib of the top section. Center the ubar side to
side on the top section. Secure each end of the u-bar to the endcap with (2)
1/4" - 20 x 11/16" self-drilling screws.
Fasten center of the u-bar as shown to the rib using (2) 1/4" - 14 x 5/8" self-
tapping screws one 6" to the left and one 6" to the right of the center of the
door section.
NOTE: Operator bracket must be mounted and secured prior to installing top
section, refer to the main Installation Instructions and Owner's manual.
©Copyright 2016 Wayne Dalton, a division of Overhead Door Corporation
Weather Seal and U-Bar Kit
Installation Instructions
for Models 8000 and 9100
Weather Seal
U-BAR
Model 9100
WEATHER
JAMB
FULLY ADJUSTABLE TRACK
WEATHER
1/8" TO 1/4"
SEAL
JAMB
(2) 1/4"-20 X 11/16"
SELF DRILLING SCREWS
ATTACHING CENTER OF U-BAR
327675
QUICK INSTALL TRACK
Q.I. JAMB BRACKET
SEAL
FULLY ADJUSTABLE JAMB BRACKET
OPERATOR BRACKET
(2) 1/4"-14 X 5/8"
U-BAR
TOP DOOR SECTION
ATTACHING ENDS OF U-BAR
REV3 5/03/2016
6"
6"
SELF TAPPING
SCREWS

Publicidad

loading

Resumen de contenidos para Wayne Dalton 8000

  • Página 1 P.O. Box 67, Mt. Hope, OH 44660 www.Wayne-Dalton.com NOTE: Use these installation instructions in conjunction with the main Installation Instructions and Owner’s Manual. This kit can only be used with Wayne-Dalton 8000 and 9100 doors 7’-0” high, 8’-0” and 9’-0” wide. QUICK INSTALL TRACK Weather Seal Q.I.
  • Página 2 U-BAR TOP SECTION Model 8000 NOTE: For door section identification, refer to the main Installation Instructions and Owner’s Manual. U-BAR U-BAR NOTE: Prior to installing u-bar, install top bracket according to the main Installation Instructions and Owner’s manual. (2) 1/4” - 20 X 7/8”...
  • Página 3 NOTA: Use estas instrucciones de instalación en combinación con las instrucciones principales de instalación y el Manual del usuario. Este juego sólo puede usarse con las puertas Wayne-Dalton 8000 y 9100 de 7 pies de altura, de 8 y 9 pies de ancho.
  • Página 4 BARRA EN U SECCIÓN SUPERIOR Modelo 8000 NOTA: Consulte la identificación de las secciones de la puerta en las instrucciones principales de instalación y el Manual del usuario. BARRA EN U BARRA EN U NOTA: Instale el soporte superior antes de instalar la barra en U, según las instrucciones principales de instalación y el Manual del usuario.

Este manual también es adecuado para:

9100