Cequent Towing Products 24745 Instrucciones De Instalación

Kink pull wire to keep
Independent of bolt
Frame
Access Slot Reinforcement
Bracket
Figure 3
Example of Fishwire Procedure
Hitch Shown In Proper Position
Equipment Required: Drill, Pull Wire (Provided)
Fastener Kit: 24745F
Wrenches: ¾"
Drill Bits: ½"
½"
Drill hole
Frame
Reinforcement
Bracket
End of
frame
Figure 2
Drill Location
Typical Both Sides
1 1 1 1 Qty. (4) Carriage Bolt – 1/2-13 x 1.75
2 2 2 2 Qty. (4) Spacer – 1/4 x 1 x 3
3 3 3 3 Qty. (2) Lock Washer – 1/2"
1. Lower exhaust by detaching it from the rubber isolator.
2. Locate 3/8" hole in frame reinforcement bracket which is welded to frame rail (see Figure 2). Center punch and drill 1/2" hole in frame rail,
enlarging 3/8" hole in frame reinforcement bracket to 1/2", both sides.
3. Fishwire spacer and carriage bolt thru access slot in frame rail and down thru hole drilled in Step 2, both sides. Use a kink in the wire due to
tight area (as shown in Figure 3).
4. Raise hitch into position, taking care not to push carriage bolts back into frame. Secure with conical washers and nuts.
Note: If vehicle is equipped with plastic appearance panel behind trunk pan, remove and return to vehicle owner.
5. Make sure hitch is centered on vehicle. Using hitch as a template, drill (2) 1/2" holes into vehicle impact bar.
6. On driver's side, install carriage bolt and spacer from open face of impact bar and down thru hole drilled in step 5. Secure with lock washer and
nut.
7. On passenger's side, fishwire carriage bolt and spacer thru end of impact bar and down thru hole drilled in step 5. Secure with lock washer and
nut.
8. Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 LB.-FT. (102 N*M)
9. Raise exhaust back into position and reattach to rubber isolator.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2005, 2006, 2015 Cequent Towing Products – Printed in México
Installation Instructions
Pontiac Pursuit (Canada Only)
Note: Does not fit Cobalt SS Coupe,
Impact Bar
Fascia
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
Rise position only.
Note: If vehicle is equipped with plastic
appearance panel behind trunk pan, it
will need to be removed and returned to
vehicle owner for hitch installation.
Access Slot
Frame Rail
Access slot
In frame rail
Muffler
Rear
Of Vehicle
Chevrolet Cobalt
Pontiac G5
Pursuit GT or G5 GT Models
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC1, PC2
Drilled Hole
Figure 1
4 4 4 4 Qty. (2) Conical Washer – 1/2"
5 5 5 5 Qty. (4) Hex Nut – 1/2-13
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Frame Reinforcement
Bracket
Impact
Bar
24745N 10-19-15
Form F206 Rev A 5605
24745
77122
60808
Rev. C