Porter Cable PXCM010-0012 Manual De Instrucciones página 3

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

RISK OF HEARING LOSS. Always wear ANSI S3.19 approved ear protection when using
the tool. Prolonged exposure to high intensity noise is able to cause hearing loss.
RISK OF EYE INJURY. Always wear ANSI Z87.1 approved safety goggles when using an
air tool. Air powered equipment and power tools are capable of propelling materials such as
metal chips, sawdust, and other debris at high speed which could result in serious eye injury.
RISK OF INJURY. Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the tool in unexpected situations.
RISK OF INJURY. Avoid prolonged exposure to vibration. Air powered tools can vibrate
during use and repetitive motion or vibration may cause injury. Avoid prolonged use of the
tool or stop using the tool if discomfort occurs.
WARNING: CONTAINS LEAD. May be harmful if eaten or chewed. May generate dust
containing lead. Wash hands after use. Keep out of reach of children.
WARNING: This product can expose you to chemicals including Lead and Cadmium, which
are known to the State of California to cause cancer and birth defects or other reproductive
harm. For more information go to www.P65Warnings.ca.gov.
TOOL USE AND CARE SAFETY
RISK OF INJURY. Do not use the tool if the trigger does not turn the tool on or off. Any
tool that cannot be controlled with the trigger is dangerous and must be repaired.
RISK OF INJURY. Disconnect the tool from the air source before making any adjust-
ments, changing accessories, cleaning or storing the tool.
RISK OF INJURY. Store the tool when it is idle, out of reach of children and other un-
trained persons. A tool is dangerous in the hands of untrained users.
RISK OF BURSTING AND/OR INJURY. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that affects the tool's operation. If
damaged, have the tool serviced before using. Do not operate the tool with the protective
guarding removed or damaged. Replace the tool or have it repaired by an authorized service
center. Many accidents are caused by poorly maintained tools or air hose. There is a risk of
bursting if the tool is damaged.
RISK OF BURSTING AND/OR INJURY. Check for damaged air hose. Keep the air hose
away from heat, oil, and sharp edges. Inspect the air hose periodically and replace it if it
becomes worn or damaged.
RISK OF EXPLOSION AND/OR INJURY. Use compressed air regulated to a maximum
pressure at or below the rated pressure of any attachments. This spray gun is designed
to operate best at pressures between 25-50 PSI. Never attempt to operate the spray gun at
pressures in excess of 50 PSI. Exceeding the maximum pressure rating of tools or acces-
sories could cause an explosion resulting in serious injury.
RISK OF EXPLOSION AND/OR INJURY. Halogenated hydrocarbon solvents—for example:
1,1,1- trichlorethane and methylene chloride—can chemically react with aluminum used in
most spray equipment and can cause an explosion hazard. Read the label or data sheet for
the material you intend to spray. DO NOT use spray materials containing these solvents.
RISK OF INJURY. Use only accessories that are designed for the specific tool. Use
of an accessory not intended for use with the specific tool increases the risk of injury to
persons.
RISK OF INJURY. Tool service must be performed only by qualified repair personnel.
RISK OF INJURY. When servicing a tool, use only identical replacement parts. Use only
authorized parts.
Use only the lubricants supplied with the tool or specified by the manufacturer.
RISK OF BURSTING AND/OR INJURY. Never connect to an air source that is greater
than 50 psi. Over pressurizing the tool is able to result in bursting, abnormal operation,
breakage of the tool, or serious injury to persons. Use only clean, dry, regulated compressed
air at the rated pressure or within the rated pressure range as marked on the tool. Always
verify prior to using the tool that the air source has been adjusted to the rated air pressure or
within the rated air pressure range.
RISK OF EXPLOSION AND INJURY. Never use oxygen, carbon dioxide, combustible
gases or any bottled gas as an air source for the tool. Such gases are capable of explo-
sion and serious injury to persons.
TOOL SERVICE SAFETY
AIR SOURCE SAFETY
3 - ENG

Publicidad

Tabla de contenido
loading

Tabla de contenido