Reelcraft LG3065 123 9Q Instrucciones De Operación página 2

Retractable Industrial Extension Cord Reel
6. The reel can now be installed into the bracket. The following
installation instruction will allow smooth retraction:
a. When the mounting height is less than 5 ft, the reel should
be positioned so that the cord opening face upward (fig. 3).
b. When the mounting height is more than 5 ft, the cord
opening should face downward (Fig. 4).
7. Slide the mounting pin (B) through bracket and reel. Slide the
locking pin (C) through the Mounting Pin for security.
Wall Mount
5Ft or Below
B
A
C
Fig. 3
Ceiling Mounting (Fig. 5)
1. Pick the approximate location for the reel with 2 1/2 ft. of a
110-125V Standard Outlet.
2. Locate a joist or beam to install the mounting bracket. The
bracket should be placed directly over the center of the joist or
beam.
3. Using the bracket as a template, mark the (3) screw locations
with pencil. (Fig.1)
4. Pre Drill (Pilot) the three screw holes with the use of at 1/4"
drill.The depth of the Pilot holes should be at least 2".
5. Install the bracket with the (3) provided head wood screws
with washers using a 1/2" wrench or socket. Tighten all three
until snug.
6. The reel can now be installed
into the bracket. (Fig.5)
7. Slide the mounting pin (B)
through bracket and reel.
WARNING: Slide the locking
pin (C) thru the Mounting Pin
(B) for security. It will prevent
the mounting pin from sliding
out of position
NOTE: When Ceiling Mounting
is to be against at steel beam, a
Professional Installer should
use minimum 1/4" bolts with
lock washers or locking nuts.
Page 2
Wall Mount
Above 5Ft
B
A
C
Fig. 4
C
Fig. 5
OPERATION
Plug power cord into any 110-125V standard wall outlet. The red
LED in the Quad-Tap will light indicating the outlets are energized.
If the indicator does not light, check power source. Plug up to
four (4) electrical appliances into the Quad-Tap outlet. Pull cord to
approximate desired length. Continue pulling the cord out slowly.
When a clicking sound is heard, stop pulling the cord. The cord
is now locked in place and is ready for use. To retract, pull the
cord out slowly until the clicking sound stops. The cord is now
unlocked and ready to retract fully.
CAUTION: To avoid possible injury. DO NOT allow the cord to fly
unrestricted back into the reel. Guide the cord back into the reel
by hand to control retraction speed. NOTE: Outlet is un-switched
and energized at all time. DO NOT OVERLOAD!
CIRCUIT BREAKER OVERLOAD PROTECTION
The reset button for the circuit breaker is located on the side of
Quad-Tap. If unit is overloaded circuit breaker will trip (black reset
button will pop out). Remove overload, wait two minutes, then
reset by pressing black button.
MAINTENANCE
WARNING: UNPLUG UNIT BEFORE PERFORMING ANY
MAINTENANCE. Remove dirt and grime as soon as it accumu-
lates. Use a soft, damp cloth and a mild soap, if needed. Be sure
not to get the electrical plug wet. NEVER submerge any part of the
Cord Reel in any solution to clean it.DO NOT USE solvents such
as gasoline, turpentine, etc. to clean unit.Keep reel cord clean to
assure smoothest automatic retraction. To clean, simply pull cord
to its full length and allow to retract through a dampened rag. Pull
out full length again and allow to retract through clean rag sprin-
kled with talcum powder. DRY THOROUGHLY BEFORE PLUGGING
BACK INTO OUTLET.
A
B
www.reelcraft.com