Publicidad
Idiomas disponibles
Idiomas disponibles
Always wear SAFETY GLASSES
when installing hitch
Scan for step by step
PHOTO installation
instruction or visit
http://www.cequentgro
up.com/qr-product.aspx
③
④
Figure 4
⑤
REMOVE PLASTIC PLUGS: Remove (3) plastic plugs from existing holes in frame rails and return to owner, use flat headed screw if necessary. Each side. Return to owner.
1.
LOWER EXHAUST: Lower exhaust system at the (3) rubber isolators. Note: Spraying a lubricant on the metal hanger rod and the rubber isolator helps with removal. Pry bar or
2.
exhaust hanger tool may be helpful.
INSTALL FASTENERS: Rear fasteners - Feed coiled end of pull wire through rearmost hole in frame and out access hole (forward hole). Slide spacer (item 2) over coiled end of pull
3.
wire and attach carriage bolt (item 1). Feed spacer then carriage bolt into access hole and out rearmost hole. See figure 2. Both sides. Forward fasteners - Attach carriage bolt
(item 1) to pull wire and slide spacer (item 2) onto pull wire. Insert carriage bolt into forward most access hole then insert spacer then pull back out access hole. See figure 3. Leave
pull wires attached.
RAISE HITCH : Raise hitch into position, feed pull wire through corresponding slots on hitch with spacer (item 5) (see figure 4 for orientation) between frame and hitch bracket at
4.
forward attachment as shown. See figure 1. Install conical washer and use to hold the bolt in place, remove the pull wires and attach the hex nut. Tighten to hold hitch in place,
repeat on all fasteners.
5.
Tighten all 7/16 GR 5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Proper torque is needed to keep the hitch secure to the vehicle when towing.
RE-ATTACH EXHAUST: Raise exhaust back into position and reattach exhaust hangers disconnected in step 2. Note: Using a spraying a lubricant helps with reinstallation.
6.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or
ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2016 Cequent™ Performance Products, Inc. -
Installation Instructions
①
②
PART NUMBERS: 76084, 84084, CQT76084
⑤
Note: Fasteners typical both sides
Rear
Figure 1
Printed in Mexico
(Conical Washer)
Teeth side
against hitch
Examples of pull wire procedure
Access hole
Kink Pull wire to keep
spacer independent of bolt
Figure 2
⑥
Sheet 3 of 15
76084NP
Fastener Kit : 76084
①
Qty.(4)
Carriage bolt
7/16-14 X 1.75 GR5
②
Qty. (4)
Spacer
.250 X .875 X 3
③
Qty. (4)
Conical washer
7/16''
④
Qty. (4)
Het Nut
7/16-14 GR2
⑤
Qty. (2)
Spacer (round hole)
.250 X 1.5 X 2
⑥
Qty. (4)
Pull wire
7/16"
⑥
Reverse pull wire
Figure 3
10-31-16
Rev. B
Publicidad
