Cequent Performance Products 45300 Instrucciones De Instalación

Vehicle
Frame
Bumper
Spring shackle
Hitch Shown In Proper Position
Equipment Required: Cable tie provided
Fastener Kit: 45300F
Wrenches: 13mm, 19mm, 21mm, 22mm, 3/4",
7/8", & 6" Ratchet Extension
Drill Bits: Short bed – 3/8", & 9/16" Rotabroach hole
cutting tool - part number 6811 (sold separately) or
carbide drill
Other items: Plastic cutting tool,
(short bed as needed. (heat shield)
Existing 14mm
bumper bolts
r
p
o
Install attachment bars
One side at a time, remove
side M14 bolts at the outside
end of the frame rail.
j
Qty. (4) Hex Bolt, M14 x 2.0 x 45mm CL10.9
k
Conical Toothed Washer, 5/8" (black color)
Qty. (6)
l
Qty. (2) Hex Bolt, M14 x 1.5 x 45mm CL10.9
m
Spacer, 1/4" X 1-1/2" X 2"
Qty. (2)
n
Qty. (2) Flange nut, M14 x 1.5 CL10
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010 Cequent Performance Products
Installation Instructions
GMC Sierra/Chevrolet Silverado 2500 & 3500 HD Pickups.
(All inc. Regular, Crew, Extended & Dually - 2 & 4WD Long & Short-bed)
GMC Denali HD Crew-Cab Pickup. Short bed trucks requires drilling
Bumper
Fascia
p q
k
n
r
Existing 14mm
bumper bolts
o
Note: Fasteners typical both sides
(coarse thread)
(fine thread)
Tighten 1/2"-13 Gr.5 bolts with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten M14 x 2.0 CL10.9 bolts to 115 Lb.-Ft. (156 N*M)
Tighten M14 x 1.5 CL10.9 bolts to 148 Lb.-Ft. (201 N*M)
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
Forward holes
l
m
Bumper
attachment
weldnuts
Frame attachment
weldnuts
p q
p
k
j
o
Qty. (2) Hex bolt , 1/2-13 x 2.00 GR 5
p
Conical Toothed Washer, 1/2" (gold color)
Qty. (4)
q
Hex Nut, 1/2"-13
Qty. (2)
r
Qty. (1) Attachment bar LH (117535)
s
Qty. (1) Attachment bar RH (117536)
Sheet 1 of 6
Part Numbers:
Max Gross
Trailer WT (LB)
18,000 (8172 Kg)
18,000 (8172 Kg)
Drilled holes both sides
Short bed only
14mm
k
j
k
Bumper attachment,
j
k
14mm weldnuts
j
Bumper , exhaust & heat shield not shown
45300N 8-25-10
Form: F205 Rev A 5-6-05
45300
Max Tongue
WT (LB)
2500 (1135 Kg)
2000 (908 Kg)
Existing 14mm
bumper bolts.
s
p o
Rev. A