Express HORNET Guía De Resolución De Problemas página 3

ENGLISH
P R O B L E M
The trigger does not work.
THE HORNET / WIZZ GUN
DOES NOT LIGHT :
The sound of gas cannot be heard when
the trigger is fully pressed.
THE HORNET / WIZZ GUN
DOES NOT LIGHT :
The sound of gas can be heard when the
trigger is pressed.
THE HORNET GUN LIGHTS
but the flame goes inside the burner.
THE HORNET / WIZZ GUN LIGHTS
but the flame produced when the trigger
is fully pressed is no larger than the
medium flame.
F R E Q U E N T L Y A S K E D Q U E S T I O N S
A small residual flame is present when the hose is emptied. Is this normal?
→ Yes, because the pressure drops below the tool's operating threshold. When this flame appears, release the trigger to stop the flame and then press the trigger again
to finish emptying.
Is it possible to use the Hornet / Wizz indoors?
→ Yes, subject to certain conditions:
• Applicable regulations in the country where the user is located must be complied with.
• Gas burners consume oxygen and release CO/CO2. A check must be carried out to ensure that the room is sufficiently ventilated before using the tool.
Propane cylinders are generally stored outdoors.
What is the maximum length of hose that can be used? → The maximum hose length is 20 metres, for reasons of safety and pressure losses.
Is it possible to disconnect the quick-release coupling while there is gas in the hose? → Yes, the quick-release coupling is self-closing.
Is it possible to change only the quick-release coupling on the hose? → Yes: Cat. No. 911.
Is it possible to use butane? → NO.
Is it possible to use natural gas? → NO.
C A U S E
The burner is in safety mode.
1
The valve on the cylinder is not open.
2
The cylinder is empty.
3
The safety on the valve, or on the regulator with gauge,
4
is in the locked position.
If the problem persists, it is caused by the gas cylinder
5
valve.
If the problem persists, it is caused by the gas used.
6
The flow limiter on the gas cylinder valve is activated
7
(France).
The gas in the cylinder is at too low a temperature
8
(frosting) and the pressure is too weak.
DISCONNECT THE TOOL FROM THE GAS CYLINDER AND CHECK IF THERE IS A SPARK IN THE BURNER
The ignition system in the burner is not working.
9
If the problem persists, the piezoelectric ignition is not
10
working.
The gas in the cylinder is at too low a temperature
11
(frosting) and the pressure is too weak.
The gas flow is too weak. See the previous points :
12
3 4 5 6 7 8
The gas in the cylinder is at too low a temperature
13
(frosting) and the pressure is too weak.
R E M E D Y
→ Put the burner in work mode.
→ Open the valve by turning it anticlockwise.
→ Replace it with a full cylinder.
→ Press on the valve button for 2 to 5 seconds, according to
the hose length.
→ Use another cylinder or a larger cylinder. Use the
EXPRESS double connection kit (Cat. No.18970) to connect
2 cylinders.
→ Check the gas: if it is butane, use propane instead!
→ Close the cylinder valve and slowly open it again.
→ Use another cylinder or a larger cylinder. Use the
EXPRESS double connection kit (Cat. No.18970) to connect
2 cylinders.
THERE IS NO SPARK
→ Try replacing the burner.
→ Use a new EXPRESS «Trigger + Piezo» set
(Cat. No. 42305).
THERE IS A SPARK
→ Use another cylinder or a larger cylinder. Use the
EXPRESS double connection kit (Cat. No.18970) to connect
2 cylinders or use a smaller burner.
→ Use another cylinder or a larger cylinder. Use the
EXPRESS double connection kit (Cat. No.18970) to connect
2 cylinders or use a smaller burner.
→ Use another cylinder or a larger cylinder. Use the
EXPRESS double connection kit (Cat. No.18970) to connect
2 cylinders or use a smaller burner.