AMT 1950 Chevrolet 3100 PICKUP TRUCK Manual De Instrucciones

6
:
A
1
79
14
12
13
B
304
300
501
501
302
302
500
7
:
8
:
A
16
400 512
( Clear Red )
503
78
505 400
( Clear Red )
B
301
507
2
303
45
29 / 28
502
511
OPTIONAL
BUMPER DECAL
OPTIONAL
Die Cut Flat Plastic Part
OPTIONAL
504
FLASHER * *
( Clear Amber )
( Die Cut Flat Plastic Part )
512
OPTIONAL
63
62
67
508
OPTIONAL
506
4
( 3 other side )
OPTIONAL
RUNNING LIGHTS
( Clear Amber )
* * FLASHER
( Drill small locating holes )
AMBER
PARTS
Brackets installed in Step 3B.
A N O F F I C I A L H E R I TA G E C H E V R O N P R O D U C T
I M P O R T A N T
Carefully study and understand the entire instruction sheet. Compare
the parts in the box to the instruction sheet to be sure you have received all
the parts required. Carefully remove parts from trees. Before cementing,
"TEST FIT" parts together to insure proper location and alignment.
Scrape paint and plating from surfaces to be cemented. Subassemblies and
components should be painted before any parts are attached. Use only
cement and paint made for styrene plastic. Painting: Wash parts
thoroughly with mild soap and water. Parting lines, glue joints, and sharp
edges should be sanded or lled with ller putty designed for plastic. Apply
a "primer" coat and allow to dry. Check parts for imperfections and repeat
the procedure if necessary. Remove any lint or dust.
Apply paint evenly, in several thin coats rather than one heavy coat.
Allow each coat to thoroughly dry before the next is applied. Each coat
should be carefully "wet sanded" using slightly damp No. 1200 sandpaper.
Be careful not to remove any detail white sanding. Lightest colors should
be painted rst. Use frosted tape to mask o areas not to be painted.
Remove tape after paint is dry to the touch. Use a very ne brush to touch
up edges. Decals: See back of decal sheet for proper application. Decals
should to be added after applying a gloss coat. Apply a nal clear coat after
decals are dry.
DECAL APPLICATION INSTRUCTIONS
1. Cut decals apart close to image. Apply one at a time.
2. Dip decal into tepid water until paper backing loosens.
3. Moisten area of model where decal is to be applied, to
aid in positioning.
4. Slide decal partly off of paper backing.
5. Place decal on model face up and slide paper
backing away.
Decal
6. Thoroughly blot out excess water, air bubbles, and any
excess emulsion with soft, lint-free cloth.
7. Allow time to dry before handling.
Paper Backing
NOTE: If air bubbles or wrinkles form on an irregular or curved surface, cut decal and press into place.
Round 2, LLC International Hobbycraft (UK) Ltd.
4073 Meghan Beeler Court 21 St. Thomas Street
South Bend, IN 46628 Bristol BS1 6JS England
Officially licensed product, trademarks property of Chevron Intellectual Property LLC. GENERAL MOTORS
Trademarks used under license to Round 2, LLC. Firestone and F Shield Logo are registered trademarks of
BFS Brands, LLC and are used with permission. AMT & design is a registered trademark of Learning Curve
Brands, Inc. used under license to Round 2, LLC. ©2011 Learning Curve Brands, Inc. All rights reserved.
Round 2 and design is a trademark of Round 2, LLC. ©2011 Round 2, LLC, South Bend, IN 46628 USA. Product
and packaging designed in the USA. Made in China. All rights reserved.
A679-201
1/25 SCALE
RECOMMENDED TOOLS
HOBBY KNIFE
Use a sharp hobby
knife to remove
parts from the
trees. e knife
may also be used
to remove parting
lines and ash.
TWEEZERS
Use tweezers to
hold small parts
during assembly,
painting and when
applying cement.
BRUSH
We recommend the
use of liquid
polystyrene
cement. Apply
with a ne brush.
Use sparingly or a
sloppy job will
result.
READ ALL LABELS AND
WARNINGS CAREFULLY
A NOTE ON SPECIAL PARTS
This kit contains small, flat factory
die-cut white plastic parts as shown
below - DO NOT THROW AWAY!
These parts are necessary for the
service truck options.
FRONT PUSH BUMPER BRACKETS ROOF FLASHER BASE
FRONT PUSH BUMPER
round2models.com