Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Bumper fascia
Vehicle frame
Exhaust hanger
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36448F
Wrenches: 3/4", 7/8"
Drill Bits: 1/2"
Spray lubricant
Vehicle frame
Exhaust hanger
5
Qty. (1)
1/2"-13 X 1-1/2" Carriage bolt
1
Qty. (1)
1/4" X 1" X 3" Carriage block
2
Qty. (1)
1/2" Hex nut
3
Qty. (5)
1/2" Conical washers
4
1.
Remove exhaust hangers both sides. Spraying a lubricant on the metal hanger rod and the rubber isolator helps removal.
2.
Raise hitch into position and insert 4" bolts and blocks through frame and hitch (2) places both sides. Install conical washers
and 1/2" locknuts. Hand tighten only.
3.
Use hitch as template to drill out slot in bottom of vehicle frame on passenger's side. Use bolt leader to install bolt and block
through vehicle frame and hitch. Install conical washer and nut. Torque this nut to 75 ft. lbs./ 102 N*M.
4.
Tighten all (4) 1/2" fasteners installed in Step 2. Tighten these bolts so that blocks clamp securely against frame and bolt just
extends through locknut.
Tighten all 1/2" hex locknuts so that blocks clamp securely against frame and bolts just extend through locknuts.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007, 2015 Cequent Towing Products – Printed in Mexico
Installation Instructions
Chrysler Sebring, All but convertible
(Sold separately)
Drawbar Kit:
36065
Drawbar must be used in the
Rise position only.
2
1
Vehicle forward
6
Important!
Tighten 1/2" standard hex nut with torque wrench to 75 lb.-ft., 102 N*M ,
Dodge Avenger, All
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Carrying
Ball Mount
Wiring Access Location: (Sebring) PC3 & PC4
Wiring Access Location: (Avenger) PC1 & PC2
8
Enlarge
existing slot
4
3
4
7
4
Qty. (4)
5
Qty. (4)
6
Qty. (4)
7
8
Qty. (1)
– These nuts will be tightened so that bolt just extends through locknut later.
Sheet 1 of 3
Manufacturer's Rating or
Max Gross
Trailer WT
3500 lb. (1589 Kg)
Existing hole in bottom of
frame for bolt leader access.
4
Note!
- Tighten 1/2" locknuts
7
so that blocks clamp securely
against frame and bolt just
extends through locknut.
1/2"-13 X 4" Gr.5 Hex Bolts
3/16" X 1-1/4" X 2" Blocks
1/2" Hex Lock nuts
1/2" Bolt leader
36448N
10-13-15
Form: F205 Rev A 5-6-05
Part Numbers:
36448
90166
06526
Max Tongue
WT
300 lb. (136 Kg)
5
6
Vehicle frame
Do not over torque!
Rev. C

Publicidad

loading

Resumen de contenidos para Cequent Towing Products 36448

  • Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 36448N 10-13-15 Rev. C 2007, 2015 Cequent Towing Products – Printed in Mexico Form: F205 Rev A 5-6-05...
  • Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 36448N 10-13-15 Rev. C 2007, 2015 Cequent Towing Products - Imprimé au Mexique Form: F205 Rev A 5-6-05...
  • Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 36448N 10-13-15 Rev. C 2007, 2015 Cequent Towing Products - Impreso en México Form: F205 Rev A 5-6-05...

Este manual también es adecuado para:

9016606526