Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Keep hands and feet clear of the nylon cutting head or blade while unit is in use.
-
Do not use this type of machine for sweeping away debris.
-
Use nylon cutting head which is free of damage. If a stone or any other obstacle is hit, stop the engine and
-
check the nylon cutting head. A broken or unbalanced nylon cutting head must never be used.
When ever approaching an operator of the machine, carefully call his attention and confirm that the
-
operator stop the engine. Be careful not to startle or distract the operator which can cause an unsafe
situation.
-
Never touch the nylon cutting head or blade when ever the engine is running. If it is necessary to replace
the protector or cutting attachment, be sure to stop the engine and confirm that the cutting device has
stopped running.
The engine should be turned off when the machine is moved between work areas.
-
Pay attention to loosening and overheating of parts. If there is any abnormality of the machine, stop
-
operation immediately and check the machine carefully. If necessary, have the machine serviced by an
authorized dealer. Never continue to operate a machine which may be malfunctioning.
In start-up or during operation of the engine, never touch hot parts such as the muffler, the high voltage
-
wire or the spark plug.
-
After the engine has stopped, the muffler is still hot. Never place the machine in any places where there
are flammable materials (dry grass, etc.), combustible gasses or combustible liquids.
-
Pay special attention to operation in the rain or just after the rain as the ground may be slippery.
If you slip or fall to the ground or into a hole, release the throttle lever immediately.
-
6.
PETROL SAFETY WARNING
WARNING: Use extra care in handling fuels. They are flammable and the vapours are explosive.
The following points must be observed.
Use only an approved container.
-
Exhaust components to cool before refueling.
-
-
Do not smoke.
-
Never refuel the machine indoors.
-
Never store the machine or fuel containers inside, where is an open flame, such as a water heater.
-
If fuel is spilled, do not attempt to start the power source, but move the machine away from the area of
spillage before starting.
Always replace and securely tighten the fuel cap after refueling.
-
If the tank is drained, this should be done outdoors.
-
Keep the handles free from oil and fuel.
-
Do not smoke while mixing fuel or filling tank.
-
Never start or run the engine inside a closed room or building. Exhaust gas contain dangerous carbon
-
monoxide.
-
Never attempt to make engine adjustments while the unit is running and strapped to the operator. Always
make engine adjustments with the unit resting on a flat, clear surface.
-
When the machine is placed in storage for a long time, drain fuel from the fuel tank and carburetor, clean
the parts, move the machine to a safe place and confirm that the engine is cooled down.
7. SPECIFIC SAFETY WARNINGS
BLADE CAN RECOIL VIOLENTLY FROM MATERIAL IT CANNOT CUT – Blade can cause you to lose
-
arms or legs. Keep people and animals 30 feet (15 meters) away in all directions. If blade contacts foreign
objects during operation, turn off engine and allow blade to come to a halt. Then check blade for damage.
Always discard blade if it is warped or cracked.
-
BLADE CATAPULTS OBJECTS THROUGH AIR - You can be blinded or injured. Wear eye, face, and leg
protection. Always clear work area of any foreign objects before using blade. Keep people and animals 10
metres away in all directions.
BLADE COASTS AFTER THROTTLE IS RELEASED - A coasting blade can injure you or bystanders.
-
Before servicing the blade, always turn off engine, and be sure coasting blade has stopped.
WARNING DO NOT USE ANY OTHER FUEL than that recommended in your manual. Always follow
-
instructions in the Fuel and Lubrication section of this manual. Never use petrol unless it is properly mixed
GB
30
Publicidad
Tabla de contenido
