Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Utility Knife
Fastener Kit: 36474F
Wrenches: 17mm
Drill Bits: None
1 1 1 1
2 2 2 2
Figure 1
Fascia not shown for clarity
1 1 1 1
Qty. (4)
Hex Bolt M10 x 1.50 x 70mm CL8.8
Note: Fascia Trimming Required. Obtain Vehicle Owner's Approval Before Cutting.
1.
Locate existing grooved area on bottom of fascia to be cut as shown in Figure 2. Cut fascia as shown to access
mounting holes in vehicle cross member.
2.
Raise hitch into position, aligning holes in hitch top plate with holes in vehicle cross member.
3.
Secure with M10 x 1.50 x 70mm hex bolts and 3/8" conical toothed washers.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2008,2015 Cequent Towing Products – Printed in México
Installation Instructions
Note: Fascia Trimming Required. Obtain Vehicle
Owner's Approval Before Cutting
Fascia
•(Sold separately)
Drawbar Kit:
36051
Drawbar must be used in the
DROP position only.
Existing
Weldnuts
Hitch Top Plate
1 1 1 1
2 2 2 2
Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft. (52 N*M)
Volkswagen Tiguan
Vehicle Cross Member
Existing Grooved Area
In Vehicle Fascia
2 2 2 2
Qty. (4)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Wiring Access Location: PC1, PC2
6-1/2"
(165mm)
Figure 2
(Looking up from under vehicle)
Fascia trimming diagram
Conical Toothed Washer 3/8"
36474N
10-13-15
Form F206 Rev A 5605
Part Numbers:
36474
06625
90191
Area to be cut for
Hitch Installation
Rev. B
Publicidad
Manuales relacionados para Cequent Towing Products 36474
Resumen de contenidos para Cequent Towing Products 36474
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2008,2015 Cequent Towing Products – Printed in México Sheet 1 of 3 36474N 10-13-15 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2008,2015 Cequent Towing Products – Imprimé au Mexique Feuille 2 de 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Sheet 3 of 3 36474N 10-13-15 Rev. B 2008,2015 Cequent Towing Products – Impreso en México Form F206 Rev A 5605...