Time Setting; Headphone; Specifications - Retekess TR613 Manual Del Usuario

5. Long press (9) button to set single loop, all loop or cancel the loop mode.
6. In the playback state, press (9) button to pause, press again to resume normal
playback.
7. Slide the Volume Control Knob (18)to adjust volume level as desired

Time Setting

1. In the shutdown state, long-press the "M" (13) button to enter time setting mode, the hour
character flashes on LCD display at the same time.
2. Press (10) or (12) buttons to adjust hour, press "M" (13) button to confirm and then
set the minute.
3. Press (10) or (12) buttons to adjust minute, and press "M" (13) button to confirm.
The system will automatically confirm the current adjustment time if there is no operation
within 5 seconds.

Headphone

You can enjoy FM stereo broadcasting by connecting the optional stereo headphones to the
Headphone jack (4) on the unit. When using headphones, sound from the speaker will be
muted.

Specifications

Power input: 5V--0.6A
Rated power: 3W
Lithium battery: 3.7V
Frequencies: FM: 88-108MH
MW: 530-1600KHz
SW: 8.0-18.0MHz
Antenna: FM/SW: telescopic antenna
MW: built-in ferrite bar antenna
Speaker: 6Ω
The maximum power without distortion: 1W
Size: 173 x 91.6 x 37.4mm
Weight: 277.6g (without battery)
Include accessories: user manual,warranty card, 18650 lithium battery, USB cable, hand strap.
3
RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE
Before using this radio, read this guide which contains important
operating instructions for safe usage and RF energy awareness
and control for compliance with applicable standards and
regulations.
ATTENTION!
Local Government Regulations
When radios are used as a consequence of employment, the Local Government Regulations
requires users to be fully aware of and able to control their exposure to meet occupational
requirements. Exposure awareness can be facilitated by the use of a product label directing
users to specific user awareness information. Your Retekess radio has a RF Exposure Product
Label. Also, your Retekess user manual, or separate safety booklet includes information and
operating instructions required to control your RF exposure and to satisfy compliance
requirements.
Unauthorized modification and adjustment
Changes or modifications not expressly approved by the party responsible for compliance
may void the user's authority granted by the local government radio management departments
to operate this radio and should not be made. To comply with the corresponding requirements,
transmitter adjustments should be made only by or under the supervision of a person certified
as technically qualified to perform transmitter maintenance and repairs in the private land
mobile and fixed services as certified by an organization representative of the user of those
services.
Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by
the local government radio management departments equipment authorization for this radio
could violate the rules.
FCC Requirements:
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
4