Adler europe AD 1187 Manual De Instrucciones página 4

device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact
professional electrician in this matter.
15. Avoid getting the device wet.
16. The device may only be wiped with a dry cloth. Do not use water or cleaning fluids.
17. The device should be kept in a dry room.
Device description:
FRONT:
1. TONE +/-
4. PREVIOUS / TUNE-
7. ALARM / MEM-UP
10. VOLUME +/-
BACK:
11. Telescopic aerial
SETTING UP
Connect the power adapter to the mains power and the power jack on the back of the radio (DC 9V).
Fully extend the radio aerial in a vertical position to obtain the maximum signal strength.
When the power is connected, the defaulted clock 00:00 will be displayed on the LCD Screen. Long press the MODE / STANDBY (8)
button to activate the unit . (This process may take a few minutes depends on different signal strength and working environment.)
The clock is defaulted to 0:00
The alarm is defaulted to 0:00 and off
GETTING STARTED
Time Set Up
Switch the radio on by pressing the MODE / STANDBY (8) button once.
Press and hold the CLK-SET / MEM (6) button to enter into clock set.
To set clock display format , press PREVIOUS / TUNE-(4) or NEXT / TUNE+(5) to choose between 12/24 Hour.
To set clock , press PREVIOUS / TUNE-(4) or NEXT / TUNE+(5) to adjust clock by 01 minute and 01 hour.
Each step needs to be confirmed by pressing the CLK-SET / MEM (6) button
Alarm Set Up
Switch the radio on by pressing the MODE / STANDBY (8) button once.
Press and hold the ALARM / MEM-UP (7) button to enter into alarm set.
To set time, press PREVIOUS / TUNE-(4) or NEXT / TUNE+(5) to adjust clock by 01 minute and 01 hour to confirm press the ALARM /
MEM-UP (7) .
To set mode, press PREVIOUS / TUNE-(4) or NEXT / TUNE+(5) to select outputs from Buzzer, Tuner, USB.
Each step needs to be confirmed by pressing the ALARM / MEM-UP (7) button.
The clock symbol will be displayed on the LCD screen after it is successfully set.
Alarm wake up
When it wakes up to TUNER, the radio will play FM program.
When it wakes up to BUZZER, Beep Tone (1) rings.
When alarm rings, you can press any button to stop the ring.
If you want to terminate the alarm, press and hold the ALARM / MEM-UP (7) button, the clock symbol is gone.
SLEEP OPERATION
Under any working mode, long press ALARM / MEM-UP (7) button to enter SLEEP mode, SLEEP mode is defaulted off and "10" will be
displayed on the LCD screen. Press ALARM / MEM-UP (7) button repeatedly to set sleep timer among 10 min, 20 min, 30 min, 40 min,
50 min, 60 min, 70 min, 80 min and 90 min, stop when you are on the timer you wish to set, the "sleep timer" will be stored
automatically.
SLEEP symbol will be displayed on the LCD screen after it is successfully set.
NOTE: Store information in your device
To turn off the device, use the MODE / STANDBY (8) function (holding the button). In this way, you will retain the time settings and time will
be visible under MODE / STANDBY (8) mode. When using device from MODE / STANDBY (8) (holding the button), the set information
is retained. If you turn off the device in the standard way (power off), you need to re-set the values such as time.
FM OPERATION
1. Press the MODE / STANDBY (8) button repeatedly until the LCD screen shows FM.
2. To scan stations manually, short press PREVIOUS / TUNE-(4) or NEXT / TUNE+(5) to adjust stations by 0.05MHz until
you get your favorite station.
2. USB Port
5. NEXT / TUNE+
8. MODE / STANDBY
12. AUX-IN
3. PLAY / PAUSE / ASM / PAIR
6. CLK-SET / MEM
9. PHONES
13. DC 9V Input
4