Chain Tension - SNOWJOE SUN JOE 24V-HCS-CT Manual Del Operador

7. While keeping the bar and chain against the mounting
surface, adjust the chain tension as needed by adjusting
the chain tensioner screw with the supplied hex key
wrench. Turn the chain tensioner screw clockwise to
tightening the chain, or counter-clockwise to loosen the
chain (Fig. 5).
8. Replace the chain/sprocket end cover by inserting the
tab located on the bottom first into the slot and position
the cover over the bar end. Tighten the end cover knob;
leave the bar loose enough to move slightly for tension
adjustment (Fig. 17).
Fig. 17
Slot
Tab

Chain Tension

Check the chain tension before using the saw when the chain
is cold. The correct tension of a cold chain is when there is no
slack on the underside of the guide bar; the chain is snug, but
you can rotate it by hand without binding.
During normal saw operation, the temperature of the chain will
increase. The drive links of a correctly tensioned warm chain
will hang approximately 0.050 in. (1.25 mm) out of the bar
groove (Fig. 18). Be aware that a chain tensioned while warm,
may be too tight upon cooling. Check the "cold tension" before
next use. The chain must be re-tensioned whenever the flats
on the drive links hang out of the bar groove (Fig. 18).
Fig. 18
Properly Adjusted Warm Chain
Flats are not
visible here
Approximately .050 in. (1.25 mm)
Chain Needs Tensioning
Flats are
visible here
End cover knob
Chain/sprocket
end cover
16
Chain Sharpening
m
WARNING!
To ensure that the saw works safely and
efficiently, it is essential that the cutting components are
well-sharpened. It is highly recommended to replace the
chain once it loses its ability to cut cleanly and safely.
It is possible, however, to sharpen the existing chain if the
sharpening is carefully performed. Any work on the chain and
bar requires specific experience and special tools. For safety
purposes, we recommend you contact an authorized
Snow Joe + Sun Joe dealer or call the Snow Joe
® ®
Sun Joe customer service center at 1-866-SNOWJOE
®
(1-866-766-9563).
Sharpening is necessary when:
• The sawdust looks like dust;
• Cutting becomes more difficult;
• The cut is not straight;
• Vibrations increase.
An authorized service center will sharpen the chain using the
right tools to ensure minimum removal of material and even
sharpness on all the cutting edges.
If you sharpen the chain by yourself, it's recommended to
purchase Sun Joe 24V-CSSHRP-LTE chain saw sharpener,
®
which can be powered by the same 24V iON+ battery with this
cordless pruning saw. Visit sunjoe.com or call the
Snow Joe + Sun Joe customer service center at
® ®
1-866-SNOWJOE (1-866-766-9563) to order.
Otherwise, use special round-section files with the right diameter
depending on the type of chain (see "Chain Maintenance Table"
pg. 20). You need a certain amount of skill and experience to
avoid damaging the cutting edges.
Sharpen the chain as follows (Fig. 19):
• Secure the bar firmly, with the chain mounted, in a
suitable vise.
• Tighten the chain if it is loose.
• Mount the file in the guide and then insert it in the tooth at
a constant angle from the cutting edge.
• Sharpen in a forward motion a few times and repeat this
on all the cutting edges facing the same way (right or left).
• To move the chain forward, use a screwdriver.
• Turn the bar over in the vise and repeat on all the other
cutting edges.
• Check that the depth limiter tooth does not stick out
farther than the inspection tool and file any projecting
parts with a flat file, rounding off the edges (Fig. 18).
• After sharpening, remove all traces of filing and dust
and lubricate the chain in an oil bath. Replace the
chain whenever:
– The length of the cutting edges decreases to 5 mm
or less;
– There is too much play between the links and the rivets.
+
®