Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATION
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts. To avoid injury from
sharp blades, handle with caution.
Prior to first use, it is important to clean the unit. Wash new blades with
warm soapy water and rinse thoroughly to remove the thin protective
oil film.
1. Place the unit on a clean, flat work surface.
2. Before each use, check that the unit is clean and the blades are in
good condition. Do not use this equipment if the blades are not in
good condition. Contact Vollrath to order a blade assembly.
3. Before each use, check for proper blade alignment. Slowly lower the
pusher head onto the blade assembly. They should slide together
with no obstructions. If there are obstructions, verify they are a
matching set. Remove the obstruction.
4. Verify that the blade assembly and pusher head assembly are the
desired size.
5. Prepare the food product to be processed. For lemons, limes and
some other fruit, the equipment will work better if the ends are cut
off of the fruit. Remove the stem scar on tomatoes.
6. Lift the handle and place the food on the blade
7. Remove your hands from the blade assembly area.
8. Place one hand on one of the legs to steady the equipment.
9. Use a strong, quick, downward thrust on the handle to push the food
product through the blade assembly.
10.Repeat this process until you have prepared enough food product
for your daily needs.
11.Clean, air dry, and then lubricate the equipment immediately after
each use. See the Cleaning section of this manual for more
information.
TROUBLESHOOTING
Problem
Unsatisfactory cutting.
SERVICE AND REPAIR
Serviceable parts are available on Vollrath.com.
To avoid serious injury or damage, never attempt to repair the unit or
replace a damaged power cord yourself. Do not send units directly to
The Vollrath Company LLC. Please contact Vollrath Technical Services
for instructions.
When contacting Vollrath Technical Services, please be ready with the
item number, model number (if applicable), serial number, and proof of
purchase showing the date the unit was purchased.
www.vollrath.com
assembly.
Might be Caused By
Improper food preparation.
Blades are dull, broken or bent.
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A.
Main Tel: 800.624.2051 or 920.457.4851
Main Fax: 800.752.5620 or 920.459.6573
Customer Service: 800.628.0830
Canada Customer Service: 800.695.8560
CLEANING
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts. To avoid injury from
sharp blades, handle with caution.
To maintain the appearance and increase the service life, clean the
equipment daily.
NOTICE: Food acids, if left on the blades, will erode and dull the
cutting edge prematurely. Always clean this food
preparation equipment immediately after every use.
1. Slide the pusher head assembly off of the guide rods.
2. Remove and save the thumb screws securing the blade assembly.
Remove the blade assembly.
3. The blade assembly is best cleaned by using the cleaning brush
accessory (sold separately) to push food particles out from the
unsharpened side of the blade assembly.
4. If you do not have the cleaning brush, use water under pressure to
push food particles out from the unsharpened side of the blade
assembly.
5. Wash the parts in warm soapy water and rinse thoroughly.
6. Allow the parts to air dry.
7. Install the blade assembly so the tabs on the blade assembly slide
into the groves of the base assembly.
8. Secure the blade assembly to the base using the thumb screws
removed earlier.
9. Lubricate the guide rods with mineral oil or a food-safe lubricant,
such as Petrol-Gel after each use.
NOTICE: Do not use cooking oil as it will become sticky and may
permanently damage the equipment.
Course of Action
Cut the ends off of the fruit to create better contact with the blades.
Replace the blade assembly.
WARRANTY STATEMENT FOR THE VOLLRATH CO.
This warranty does not apply to products purchased for personal,
family or household use, and The Vollrath Company LLC does not offer
a written warranty to purchasers for such uses.
The Vollrath Company LLC warrants the products it manufactures or
distributes against defects in materials and workmanship as specifically
described in our full warranty statement. In all cases, the warranty runs
from the date of the end user's original purchase date found on the
receipt. Any damages from improper use, abuse, modification or
damage resulting from improper packaging during return shipment for
warranty repair will not be covered under warranty.
For complete warranty information, product registration and new
product announcement, visit www.vollrath.com.
Technical Services
techservicereps@vollrathco.com
Induction Products: 800.825.6036
Countertop Warming Products: 800.354.1970
All Other Products: 800.628.0832
©
2017 The Vollrath Company L.L.C.
Part No. 2350025-1 ml
1/24/17
Publicidad
