Digi Sport Instruments DT710 Guia De Inicio Rapido página 6

www.digisportinstrument
s.com
INSTRUCTION
MANUALSCOREBOARD
DT710
FEATURES:
- 24 hour clock display
- Count up timer with range to 9 hr. 59 min.
59 sec.
- Countdown timer with loud beep
- Large 4 inch LCD digits for viewing from as
far away as 50M (150 feet)
RF remote control – no cords
-
required
- Powered by AC adapter (included) or
batteries (four D size – not included)
- Wall mounted or free standing
- 16 different RF channels, user-adjustable
to another channel to avoid interference
with nearby units
LIST OF ACCESSORIES
- Wall Timer
- Remote control with four AAA batteries
- Stands
- AC adapter (For indoor use only)
- Instruction manual
HOW TO OPEN NAME PLATE DOORS
Use a suitable screwdriver to open the
side doors as shown in Figure
2. Do this carefully to not damage the
plastic side doors. This allows the
removal or insertion of the nameplates
and ads.
FIXING THE WALL TIMER
The Wall Timer can be fixed on the wall
with two screws hooked into the eyelets on
the back top housing. Make sure the
screws are securely fixed into the wall. The
Wall Timer can also stand-alone on the
floor or on a table using the stands of the
Wall Timer as shown in Figure 3.
POWER UP:
- For AC connection, use only the AC
adapter (9V) supplied with the unit. Check
the power rating indicated on the adapters
is the same as the AC power supplied in
your location. Plug the adapter into the
socket on the right side of the Wall Timer
as shown in Figure 3. The digits will light
up automatically and be ready for setting.
When AC power is not available, insert four
D size batteries into the
compartment on the back of the Wall Timer
as shown in Figure 4. When using
batteries, the ON/OFF SWITCH can be
used to turn the Wall Timer on and off. If
the batteries are left in the Wall Timer
during AC operation, they serve as a back
up in the event of AC power interruption.
The volume switch is used to turn the
volume to HIGH, LOW or OFF. The
scoreboard remote control needs four 1.5V
AAA size batteries to operate as shown in
Figure 5.
TIME SETTING:
From the Time Display Mode with display
(as shown in Figure 6). Press and hold
<MODE> for 3 seconds to go to the Time
Setting Mode with display (as shown in
Figure 7). In this mode press <SET> once
for time setting and the time digits will blink.
Adjust the minute by using the <+/-TEAM
2> and the hour by using the <+/-TEAM 1>.
When time is set, press <SET> for exit to
the Time Display Mode.
COUNT UP MODE:
When the Wall Timer is in the Time Display
Mode, press and hold <MODE> 3 seconds
and repeat this action once more. It will
enter the Count Up Mode with the display
showing "C UP" as shown in Figure 8.
Press <SET> once and 0:00:00 will be
displayed. Press <START/STOP> to start
and press again to stop the count up timer.
After timing is stopped, press and hold
<SET> 3 seconds for resetting to zero.
COUNT DOWN MODE:
When the scoreboard is in the Time
Display Mode, press and hold <MODE> 3
seconds and repeat this action twice to
enter the Count Down Mode with the
display showing "C dn", as shown in Fig. 9.
Press <SET> once to enter SET COUNT
DOWN MODE. The previously set
countdown time digits will be blinking.
Press <+/- TEAM 1> to adjust the minutes
and hours. Press <+/- TEAM 2> to adjust
the seconds. When the countdown period
is set, press <SET> once and the time will
be stored in memory. The countdown timer
can be started and stopped by pressing
<START/STOP >. At 0:00:00 the
scoreboard will give a long beep to indicate
that the time is up. The countdown period
can be reset to the memorized period by
pressing and holding <SET> for 3 seconds.
If setting of countdown period is desired at
this stage, press <MODE> momentarily to
enter SET COUNT DOWN MODE and set
using the <+/-> Buttons as before.
battery