Publicidad
Idiomas disponibles
Idiomas disponibles
®
1000749 VALETO
SMART HOME SYSTEM Water Leak Sensor
ENGLISH
The VALETO® Watersensor is a battery driven, independently mounted electronic
control unit and warns when water has been leaked out.
The alarm is generated by an acoustic signal. When the device is integrated into the
VALETO® app a notification is send to the mobile device.
Technical Data
Battery: CR123A (3V)
Transmitting frequenzy: 2,4GHz
Transmission power: 5mW
Transmission range: 30 m
Mode of functioning Type 1
Degree of contamination 2
Function
The alarm is activated when the two metal pins of the probe (A) touch water. The
alarm may only be interrupted by removing the probe from the water and no
electrical connection between the two pins exists.
Place of operation
The Valeto® System may only be operated in private areas and not in commercial
areas. The device may only be used indoors.
Operate the device in areas in which the risk of an unwanted water leakage is high.
It is recommended to place the probe near to a potential leakage.
The probe must be placed on a smooth, levelled and not absorbing surface, providing
that both metal pins have an evenly contact to the ground.
When operated on carpets or similar surfaces it is not ensured that the alarm is
triggered on time.
Installation
The radio unit (B) ist suitable only for wall installation.
Install the device as shown in the figure. Remove the isolating strip from the battery..
The alarm sounds briefly.
Testing the device
Touch both metal pins with one finger. When the alarm sounds the device is working
properly. The device must be checked regularly for proper function.
Changing the battery
Use only batteries of type CR123A(3V).
Open the battery compartment on the back.
Remove the used battery (see note on used batteries).
Insert the batteries considering the right polarity into the battery compartment.
Wrong polarity may lead to explosion and/or chemical burn!
Close the battery compartment.
Intergration into the VALETO® App
Notice: For this at least one Gateway must be integrated within the app.
Open the VALETO® app on a mobile device.
Choose the Gateway to which the device should be added.
Choose <Add device> within <Settings>.
Push button (C) on the device for five seconds. The LED on the front flashes.
Choose <Smart Device> next. After that a search run is started.
When the search run is finished choose the displayed device.
After a period of 90 seconds the device is ready for operation.
Removing from the VALETO® App
Open the VALETO® app on a mobile device.
Choose the Gateway from which the device should be removed.
Within <Settings> choose <Device Mangement> and then <Sensor>.
A list of connected sensors appears.
Applying a long push on the sensorthat is supposed to be removed leads to the
details of the sensor.
Choose <Settings> and then <Delete Device>.
Disposal (European Union)
Do not dispose the product with the regular household waste! Products marked with
this sign must be disposed according to the directive(WEEE, 2012/19) on electrical
and electronic devices at local collection points for such devices!
Notes on used batteries:
Do not throw used batteries in the regular household waste. Discard the batteries at
a public collecting point or at the retail store where the batteries were purchased.
Return only completely discharged batteries. Cover the terminals before storage or
disposal to avoid short‐circuits.
Hereby, SLV GmbH declares that the radio equipment described here is in compliance
with Directive 2014/53/EC. The full text of the EU declaration of conformity is available
at the following internet address:
www.slv.com/jump/1000749
This radio equipment may be distributed in all countries of the EU.
1000749 08.12.2017 © SLV GmbH, Daimlerstr. 21‐23, 52531 Übach‐Palenberg,
Germany, Tel. +49 (0)2451 4833‐0. Technical Details are subject to change. Made in
China.
B
C
+
A
CR123A 3V
2
3
3
(cm)
8 mm
Publicidad
