ATON DLA2 Guía De Instalación Rápida

Start Here
Run all speaker wiring (16 gauge is recommended) and control wiring (Cat5)* to the DLA2/4/6.
Be sure to label the wires for easy identification.
Place the DLA2/4/6 in the same equipment location as the Receiver/Amplifier.
Turn off all power to the Receiver/Amplifier and make sure the DLA2/4/6 power supply is unplugged!
Strip approximately 3/8" of insulation from the ends of all speaker and control wiring.
Twist the exposed end of each speaker wire to ensure that no loose strands remain.
* If applicable. Cat5 is used for touch pad and IR receiver wiring.
1
Choose Receiver/Amplifier Type
A
Stereo Receiver with "A/B"
To local speakers To DLA input
Connect
to the "B"
– –
speaker
terminals.
L
R
Speaker Wire
B
Home Theater Receiver with "A/B"
To local speakers To DLA input
Connect
to the "B"
– –
speaker
terminals.
L
R
Speaker Wire
C
Home Theater Receiver with "Zone 2"
To DLA input
Connect
to the
–
"Zone 2"
speaker
L
terminals.
Speaker Wire
NOTE: Refer to your receiver manual for help
activating your "Zone 2" speaker outputs.
4
Set Impedance Dipswitches.
Amplifier Dipswitch:
Set to Receiver/Amplifier Impedance – 8 or 4 Ohms.
(Refer to receiver/amplifier manual for its specific impedance)
Speaker Dipswitch:
Set to Average Speaker Impedance – 8 or 4 Ohms.
(Refer to each speaker manual for its specific impedance)
9
If using a Receiver with "A/B" speaker outputs:
OR
the speakers connected to the DLA both the "A" speakers and those
connected to the DLA
NOTE: When using the "A+B" setting, the receiver volume will need to be adjusted accordingly.
When the DLA2/4/6 is not in use, turn off the "B" speakers and turn on
the "A" speakers for normal stereo/surround sound listening.
Please consult your owner's manual for additional installation examples, applications and safety instructions.
+
–
–
+
+
–
–
+
–
R
+
–
–
+
5
Plug in the DLA2/4/6 6
Power Supply.
10 11
Turn on one room While listening to the room turned
from the front panel on in the previous step, slowly adjust
of the DLA2/4/6 and the Receiver/Amplifier volume to
adjust volume level a level that is the loudest it can
to maximum. play in the room without distortion
or clipping. Make a note of the
volume level for future reference.
Speaker Wire
WARNING! Do not connect speakers to the DLA2/4/6 that have an impedance value lower than what is supported
by your receiver/amplifier. In doing so, you run the risk of overheating and damaging both the DLA2/4/6 and your
receiver/amplifier! Consult speaker and receiver/amplifier manuals for their specific impedance ratings.
2
Connect Speakers
Be sure to connect
the positive speaker
wire to the positive
input of the
speaker and the
negative speaker
wire to the negative
input of the speaker.
– –
+ +
3
Choose Method of Control
Connect the RF Receiver
to the ATON Port
IR S G V
White/Green (+12V)
Brown (Ground)
Orange (Status)
White/Blue (IR)
Red
Black
Yellow (Do Not Connect)
White
Turn on the Receiver/ 7 Adjust the Receiver/ Receiver/
Amplifier and start Amplifier
audio source (CD volume
player, radio, etc.). to the
lowest level. el.
Power Start Receiver/Amplifier
Audio Source Volume Knob
12
rned Finally, turn on each room
adjust from the front panel of the
to DLA2/4/6 and adjust to a
an comfortable listening level.
rtion
e
ce.
Receiver/Amplifier
Volume Knob
3/8"
3/8"
Cat5 Wire
– –
+ +
Optional
RJ11
White/Green (+12V)
Brown (Ground)
White/Blue (IR)
8 Set the Receiver/
Amplifier to stereo
mode and disable
any surround
sound or DSP
"Sound Fields."
!