Vimar ELVOX 7549 Manual Do Instalador página 3

The instruction manual is downloadable from the site www.vi-
mar.com
Description
Wall-mounted Tab monitor for Due Fili Plus system with 4.3 in LCD
colour display, handset, loudspeaker for calls, capacitive keypad
for interphone functions (unlocking, self-starting, auxiliary services,
volume, brightness and contrast controls) and intercom calls.
It is possible to differentiate the call chimes. The visual signals
are for "door/gate open," "missed calls," "user away" and "chime
muting."
Desktop installation is possible with the desktop base accessory
753A and the interconnecting stud 753B (sold separately). Wall
mountable also on 8-module back boxes (Vimar V71318, V71718)
with mounting frame 753S (sold separately).
* Article 7549 can be used by people wearing hearing aids.
Technical characteristics
• Surface-wall mount or box installation. Can be fitted to the wall
with plugs or a 3 modules (Vimar V71303, V71703) or circular
60 mm flush-mounting box (Vimar V71701).
• LCD 4.3 in 16:9 display, resolution 480x272 pixels
• Minimum signal level on the bus in reception: -20 dBm
• Capacitive touch keypad with backlit symbols.
• Power supply for terminals 1, 2 (28 Vdc).
• Absorption:
- on standby: 10mA
- maximum conversation current: 180mA
- peak current limited to call time: 180mA
• Ambient class: Class A1 (indoor use)
• Protection class: IP30
• Operating temperature: -5° to 40°C
• Operating ambient humidity 10 - 80% (non-condensing)
• Electronic chimes with different tunes (10).
• Input for landing call.
• Dimensions: 160x180x45 mm
• DIP switch for line impedance termination.
Audio frequency function for hearing aids
Art. 7549 can be used by people wearing hearing aids.
However, for correct operation of the hearing aid refer to its in-
struction manual. Any metal objects or electronic equipment
nearby may compromise the quality of the sound received by the
hearing aid.
Installation
Important: We recommend installing the device approximately
160 cm above the floor, making sure it is not exposed to direct
light, so as to avoid bothersome reflections on the surface of the
LCD screen.
Note: Fig. 1 shows the recommended installation distances, un-
less otherwise specified by current regulations.
1. Secure the plate to the wall with plugs or on a box 3 modules
(Vimar V71303, V71703) or a circular mounting box size 60mm
(Vimar V71701).
2. Wire the terminal block (Fig. 6).
3. Terminate the video signal (Fig. 5)
4. Install the monitor as follows: position the monitor on the cou-
pling plate keeping it slightly raised. While keeping the face
plate pressed, apply a light downward pressure until it clicks
EN
into place.
5. Should you need to remove the monitor you need to apply a
light pressure on the lever (Fig. 3) and raise it (from the bottom
upwards) so as to release the monitor from the chassis.
Maintenance
Clean using a soft cloth. Do not pour water onto the appliance and
do not use any type of chemical product.
Swiping your palm over the keyboard locks the buttons and all the
LEDs will blink for 5 seconds. The 5s timeout is renewed every
time a button is touched. After the 5s timeout the monitor will emit
another warning beep.
Warnings for the user
Do not open or tamper with the appliance.
In the event of trouble, call in specialized personnel.
INSTALLATION RULES
Installation should be carried out observing current installation
regulations for electrical systems in the Country where the prod-
ucts are installed.
CONFORMITY
EMC directive
Standards EN 60065, EN 61000-6-1, EN 61000-6-3 and EN
60118-4.
INFORMATION FOR USERS UNDER DIRECTIVE
2012/19/UE (WEEE)
In order to avoid damage to the environment and human
health as well as any administrative sanctions, any appli-
ance marked with this symbol must be disposed of separately
from municipal waste, that is it must be reconsigned to the dealer
upon purchase of a new one. Appliances marked with the crossed
out wheelie bin symbol must be collected in accordance with the
instructions issued by the local authorities responsible for waste
disposal.
This product was developed using FreeRTOS
www.freertos.org/
TM software - http://
3