Publicidad
Idiomas disponibles
Idiomas disponibles
VESTA MONITOR GB2
SAFETY PRECAUTIONS
- Install or modify the equipment
without the power connected
- The installation and handling of these equipments must be performed by
- The entire installation must be at least
40 cm.
- Do not use excessive force when tightening the connector screws.
- Install the
monitor
in a dry and protected place without risk of drip or water projections.
- Avoid to place it near to heating sources, in dusty locations or smoky enviroments.
-
Before to connect the system, check the connections between door panel power supply
and monitors.
-
Do always follow the enclosed information
( )
CHARACTERISTICS
*
- Handsfree monitor.
- 3,9" TFT colour screen.
- Monitor with simplified installation (2-wire bus withouth polarity).
- Capacitive buttons for access and selection of menu functions.
-
User menu
.
- Installer setup.
- Screen and volume settings menu.
- Start / end push button.
- Door release push button.
- S
tatus
Leds.
- Configuration dip-switch for monitor address code (call code).
SYSTEM OPERATION
- To make a call the visitor should press the push button corresponding to the desired apartment;
an acoustic tone will be heard confirming the call is in progress once the push button has been
pressed and the led
will turn on. If the v
progress will be heard confirming
the call is in progress. At this moment the apartment's
"
monitor(s) receives the call. During the call the visitor can correct his call by pressing a push
button corresponding to a different apartment, in which case the original call is cancelled.
- The call lasts for 40 seconds. Without alerting the visitor, their image is displayed on the master
monitor to receive the call.
For Kit villa application
displayed on monitor (
with address code
is in the apartment
2")
to receive the call
.
"
If the call is not answered in
40 se onds,
c
the
- To establish communication, press the push button
will turn on.
- Communication will last for one and a half minutes or until the button
the communication has finished, the leds
v
ocal ynthesis is enabled the message
s
,
panel
confirming
the communication has finished.
- To open the door, press the door release push button
with one press, the door release operates for 5 seconds, the led
the v
ocal ynthesis is enabled the message
s
,
- The monitor push buttons description is shown on page 3.
( ) For more information see user manual
"TVESTA GB2 (c d. 50121653)".
*
https://doc.golmar.es/search/manual/50121653
.
authorised personnel
away from any
other installation
.
,
, distribu
.
ocal ynthesis is enabled the message call is in
s
: without alerting the visitor, their image is
0 "
apartment
1"
or
monitor
with address code
16
led
will turn
off and the system will be freed.
of any monitor to the apartment
, door panel led
is pressed again. Once
& will turn off and the system will be freed. If the
"communication is finished"
will be heard
during call or communication progresses:
will also turn on for 5 seconds. If
"door is open"
will be heard
in the door panel.
o
2
VESTA MONITOR GB2
MONITOR DESCRIPTION
( )
*
.
tors
a. Microphone.
b. 3.9" TFT colour screen.
c. Menu push buttons.
d. Status leds.
e. Function push buttons.
f. Loudspeaker.
Function push buttons:
Start/ end communication push button.
During standby: Door panel image is shown.
If memory module MM-GB2 exists, recorded
video of the last call from the door panel is
displayed.
Door release push button.
( )
*
Configuration monitor address code (call code):
Kit 1 apartment
APARTMENT 1
VESTA
"
CODE 0
if the call
( )
1
Kit 2 apartments: The monitor with code 16 is the last,
MONITOR INSTALLATION
( )
*
Positioning
in the door
1.60m
( ) For more information see user manual
*
https://doc.golmar.es/search/manual/50121653
a
b
c
d
e
f
Status leds:
Kit 2 apartments
Dip6: Placed to ON to con gure with the end of line resistor in monitors
APARTMENT 1
APARTMENT 2
where bus wires terminate. Set to OFF only for intermediate monitors.
VESTA
VESTA
Dip1 a Dip5: To con gure monitor address code (address 0 to 31).
The switches set to OFF have null value. The values of the switches set
to ON are shown in the closed chart.
The address code monitor will be calculated as the sum result of the
switches values set to ON:
( )
1
C D
O E 0
C D
O E 16
Values chart
Switch number: 1
ON value:
end of line dip 6 must be set to ON.
Surface
4 30
x
"TVESTA GB2 (c d. 50121653)".
3
g
h
i
j
k
g. Attachment holes.
h. Horizontal wiring input.
i. Installation Bus terminals.
j. Connector.
k. Con guration dip-switch.
Power supply status LED.
LED indicating there are call videos
from the door panel to be viewed.
"Do not disturb" mode activated LED.
Building
ON
DIP
2
3
4
5
1
2
3
4
5
6
1
2
4
8 16
Example: 0 + 0+4+0+16 = 20
Embedding box
Supplied screws with
the embedding box.
o
Publicidad
