Power Flex 310423008 Guia Del Usuario

REPLACEMENT HOSE
AND ADAPTOR
AP31014
WARNING:
To reduce the risk of injury, user must read and understand
the operator's manual for their pressure washer before
using this accessory. Fits most pressure washers. Ensure
compatibility and proper fit before using this accessory.
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Risk of fluid injections, do not
point at people, pets, electrical devices, or the unit itself.
Turn off the pressure washer before changing or adjusting
accessories. For cold water use only. Save these instruc-
tions. Refer to them frequently and use them to instruct
other users. If you loan someone this tool, loan them these
instructions also. Do not use this accessory if any parts
appear to be missing or damaged.
PACKING LIST
25 ft. Replacement Hose
15 mm Adaptor with O-Ring
Instruction Sheet
PRODUCT SPECIFICATIONS
Maximum Pressure .......................................up to 3100 psi
Maximum Water Temperature ................................... 140°F
Maximum Gallons Per Minute .................................. 7 gpm
Adaptor Size .............................................................15 mm
USING THE REPLACEMENT HOSE
Connect the replacement hose to your pressure washer
and spray wand following the instructions provided in your
pressure washer Operator's Manual.
This high pressure hose features an outer covering that
provides strength to the hose. If the outer covering becomes
damaged, the hose must be replaced immediately. Do not
use a high pressure hose if the outer covering is damaged.
To prevent damage to the outer covering:
n Inspect the hose before every use.
n Fully unwrap and straighten hose before use.
n Do not allow the high pressure hose to be kinked.
n Keep hose away from hot surfaces and sharp edges.
n Do not pull unit by high pressure hose.
n Do not allow hose to be crushed or wrapped around
objects.
USING THE ADAPTOR
See Figure 1.
If you experience a leak at the hose connection on either
the trigger handle or pump side when using this hose, install
the adaptor provided.
n Apply silicon grease (not provided) to the edge of the o-
ring.
n Slide the adaptor over the hose connection as shown in
figure 1.
n Install the hose to the pressure washer pump or trigger
handle as desired.
TECHTRONIC INDUSTRIES NORTH AMERICA, INC.
988000-524
2-10-11 (REV:01)
If the hose connection continues to leak or if you experience
leaks on both sides, reference the part numbers that follow
and call our Customer Service Center to order an additional
adaptor or replacement o-rings as needed.
n 15 mm Adaptor with O-Ring ......................... 310423008
n 15 mm Adaptor O-Ring ................................ 570742044
n 14 mm O-Ring .............................................. 570742043
To use this replacement hose as an extension hose between
your pressure washer and your original high pressure hose,
you will also need AP31043 PowerCare M22 x M22 Hose
Adaptor, available where you purchased this replacement
hose.
CALIFORNIA PROPOSITION 65
WARNING:
This product and substances that may become airborne
from its use may contain chemicals, including lead,
known to the State of California to cause cancer, birth
defects, or other reproductive harm. Wash hands after
handling.
Fig. 1
A – 15 mm O-ring (joint torique de 15 mm, anillo "o" de
15 mm)
B – Adaptor (adaptateur, adaptador)
C – Hose nozzle (embout de tuyau, boquilla de la manguera)
D – 14 mm O-ring (joint torique de 14 mm, anillo "o" de
14 m)
E – High pressure hose (tuyau de haute pression, manguera
de alt a presión)
P.O. Box 35, Highway 8
Pickens, SC 29671, USA
1-866-340-3912
A
B
C
D
E