Technical Specifications - Bentel Security PREMIUM Serie Guia De Inicio Rapido

WARNING - DO NOT connect the Keypad to the bus when the bus is live; if this is not possible connect the bus terminals in the following order: -, +, R, C.
INTRODUCTION
PREMIUM Line is a series of Keypads controlling anti-burglary circuits which have
been realized with Kyo Unit series control panels or with Kyo100, Kyo300 and
Kyo320 control panels.
These instructions refer to the installation, programming and connection of the
Keypad; for further information on its use with the above mentioned control panels,
read the instructions provided with the said panels.
The keypad is available in 2 versions:
BKP-LCD - Keypad with an LCD display of 2 lines and 16 digits;
BKP-LED - Keypad with 16 LED.
In these instructions the generic term "Keypad" is used to refer to both versions; the
term "LCD Keypad" to refer to the BKP-LCD version, the term "LED Keypad" to refer
to the BKP-LED version.
The Keypad has a built-in Proximity Reader compatible with PROXY series Activators
and PROXY-CARD Circuit Boards.
It is also provided with 3 terminals which can be programmed to function as 3 zones
(Input expander); 3 outputs (Output expander); or 2 zones and 1 output.
The zones can operate in normal mode, connecting movement detectors, or as
interface connecting contacts for roller blinds.
The outputs are of open-collector (O.C.) type or rather floating or connected to Earth.
The Keypad is planned to work with the new communication protocol BPI-2.
The Keypad is provided for flush or surface mounting, or on type 503 boxes or
similar, by means of the appropriate BKP-BOX kit which is supplied on request.
The Keypad is provided with devices for the detection and raising of an alarm
against tampering and snatching attempts.

TECHNICAL SPECIFICATIONS

'(6&5,37,21
3RZHU 6XSSO\
&XUUHQW 'UDZ
7HPSHUDWXUH 5DQJH
'LPHQVLRQV : [ + [ ' PP
 7KH .XUUHQW GUDZ YDULHV D.. WR ZRUNLQJ .RQGLWLRQV 7KH PLQ YDOXH
UHIHUV WR ZRUN DW UHVW .RQGLWLRQV DEVHQ.H RI OLJKW DQG SUR[LPLW\ UHDGHU DW
UHVW WKH PD[ UHIHUV WR ZRUN ZLWK OLW NH\SDG DQG SUR[LPLW\ UHDGHU RQ
IDENTIFICATION OF PARTS
Figures 2 and 3 show the LCD Keypad designs (the LED Keypad differs only in a
LED instead of an LCD display) with its various parts numbered: the numbers in
boldface shown in square brackets [ ] in the followign paragraphs refer to the parts
shown in Fig.2 and Fig.3 and are being described in the following table:
 %DVH IRU IOXVK PRXQWLQJ
 &OLSV WR EOR.N WKH IURQWSODWH
 7HUPLQDO ERDUG IRU .RQQH.WLRQV
 $Q.KRU V.UHZ KROHV IRU PRXQWLQJ RQ PRGHO  ER[ RU VLPLODU
 &DEOH HQWU\
 $Q.KRU V.UHZ KROHV IRU IOXVK PRXQWLQJ
 &OLSV IRU IL[LQJ RI IURQWSODWH
 2SHQLQJV IRU WKH UHPRYDO RI WKH IURQWSODWH
5HPRYDEOH SDUWLWLRQ IRU WKH SDVVLQJ RI YLVLEOH .KDQQHOOHG ZLUHV
 )URQWSODWH /&' YHUVLRQ
 $QWLVQDW.K UDZOSOXJ
 &RQGX.WLYH SLQ IRU .ORVLQJ RI DQWLWDPSHU .RQWD.W
 /HYHO 9LDO
 6HQVLWLYH DUHD RI RI SUR[LPLW\ UHDGHU 352;<
 %DVH IRU VXUID.H PRXQWLQJ VXSSOLHG RQ UHTXHVW ZLWK %.3%2; NLW
 'HULYDWLRQ ER[ IRU VXUID.H PRXQWLQJ VXSSOLHG RQ UHTXHVW ZLWK %.3%2; NLW
 ([SDQGHU V.UHZV  IRU IL[LQJ RI WKH EDVH WR WKH GHULYDWLRQ ER[
 :DOOSOXJ IRU IL[LQJ WKH DQWLWDPSHU VZLW.K SOXJ QRW VXSSOLHG
 6HOIWDSSLQJ V.UHZ IRU IL[LQJ WKH DQWLWDPSHU VZLW.K SOXJ QRW VXSSOLHG
0LQ 7<3( 0D[
 9..  9..  9..
 P$  P$  P$
ƒ ·  ƒ&
 ;  ; 
G ENGLISH
G G G G
SURFACE MOUNTING
For surface installation of the Keypad, follow the procedure described below
(see fig. 2 at the end of the instructions):
1) Insert a sharp screwdriver into openings [8] to release the hooks [2], then
remove the cover [10] taking care to slide the terminal board out delicately;;
2) Pass the connection wires through the opening [5];
3a) If it is to be flush mounted, use the holes [6] to fix the base [1] to the wall;
3b) If it is to be mounted on a model 503 box or similar, use the holes [4] to fix
to the base [1];
To fix the keypad perfectly, use with the perforated sphere [13] at the base.
4) Fix the anti-tamper plug [11];
5) Make the keypad connections using the terminal board [3];
6) Reposition the frontplate [10] by first hooking it to the clips [7], then by blocking
it by applying light pressure until the clips are released [2].
RECESSED MOUNTING
For recessed installation of the Keypad, using the BKP-BOX kit, follow the pro-
cedure described below (see fig. 3 at the end of the instructions).
1) Embed the recess box [16] supplied with the kit, at the designated point.
2) Insert into the wall, in line with the hole in the anti-tamper plug [11], a 6x30
mm wall-plug or similar (NOT supplied) [18].
3) Pass the cables for the connections through the openings [5] in the backplate
[15] supplied in the kit.
4) Fix the backplate [15] to the recess box [16] using the screws [17] supplied
in the kit: use the spirit level [13] to position the backplate correctly.
5) Fix the anti-tamper plug [11] to the wall-plug [18], using a 4x60 mm self-
tapping screw or similar (NOT supplied) [19].
6) Proceed as for surface installation, ignoring steps 2, 3 and 4.
DESCRIPTION OF THE TERMINALS
This paragraph synthetically describes the Keyboard terminals. The table in
this paragraph uses the following terms:
¾ column M. gives the abbreviations of the terminals;
¾ column DESCRIPTION gives a synthetic description of the terminal;
¾ column v (V) gives the voltage, in volts, as on the corrisponding terminal (the
symbol "–" indicates that it is not possible to specify a voltage value);
¾ column I (A) gives the maximum current, in ampere, which could move along
on the corrisponding terminal (the symbol "–" indicates that it is not possible to
specify any value).
0
3RVLWLYH SRZHU VXSSO\
& &RPPDQG
5 5HVSRQVH
± 1HJDWLYH SRZHU VXSSO\
7 ¸ ,QSXW RU 2XWSXW =RQHV D..RUGLQJ
7 WR WKH ([SDQGHU IXQ.WLRQ PRGH
2XWSXW 3RZHU 6XSSO\ SRVLWLYH SURWH.WHG
) E\ VHOIUHVHWWLQJ IXVH IRU WKH GHYL.HV .RQQH.WHG
WR WKH NH\SDG
 6HH WKH WH.KQL.DO VSH.LIL.DWLRQV
 7KH 7 2XWSXW ([SDQGHU WHUPLQDOV .RXOG DW WKH PRVW H[.KDQJH $
7R H[.KDQJH JUHDWHU .XUUHQWV XVH 5HOq6.KHGXOH %50
PROGRAMMING
NOTE - To avoid any accidental or unauthorized programming, access to
programming is ONLY possibile if less than half an hour has passed from the
last BPI reset effected from the control panel. BPI resetting occurs every
time the Keypad is powered up, and on exiting from the installer menu.
To program the Keypad, follow the procedure described in this paragraph.
Remember that pressing the ENTER key confirms the input values and a move
forward is made to the next step while each pressing of the ESC key cancels the
input values and a step backwards is made (up to exiting the programming
phase).
'(6&5,37,21 Y 9 , $

± ±
± ±
 ±
±