Publicidad
Enlaces rápidos
The Ultimate in Fall Protection
This manual is intended to meet the Manufacturer's Instructions as required by ANSI Z359.1 &
CSA Z259.2.1 and should be used as part of an employee training program as required by OSHA.
WARNING: This product is part of a personal fall arrest or restraint system. The user must follow the
manufacturer's instructions for each component of the system. These instructions must be provided to the
user of this equipment. The user must read and understand these instructions before using this equipment.
Manufacturer's instructions must be followed for proper use and maintenance of this equipment. Alterations or
misuse of this equipment, or failure to follow instructions, may result in serious injury or death.
WARNING: IMPORTANT: If you have questions on the use, care, or suitability of this equipment for your
application, contact DBI/SALA.
WARNING: Record the product identifi cation information from the ID label in the inspection and maintenance
log in Section 10 of this manual.
Form: 5902127 Rev: K
Instructions for the following series products:
User Instruction Manual
Vertical Lifelines and
Vertical Lifeline Subsystems
Figure 1 - Vertical Lifeline Assemblies
1202749 (3/4" polyester/polypropylene rope, 30 feet)
1202753 (5/8" polyester/polypropylene rope, 30 feet)
1202750 (3/4" polyester/polypropylene rope, 30 feet)
1202754 (5/8" polyester/polypropylene rope, 30 feet)
5901003 (3/8" wire rope, 30 feet)
Rope Cut to Length
Vertical Lifelines
Vertical Lifeline Subsystems
(See back pages for specifi c model numbers.)
5/8" polyester/polypropylene rope
5/8" polyester rope
3/4" polyester/polypropylene rope
3/4" polyester rope
3/8" 7x19 wire rope
© Copyright 2012, Capital Safety
Publicidad
Manuales relacionados para DBI SALA Vertical Lifeline
Resumen de contenidos para DBI SALA Vertical Lifeline
- Página 1 WARNING: Record the product identifi cation information from the ID label in the inspection and maintenance log in Section 10 of this manual. Figure 1 - Vertical Lifeline Assemblies 1202749 (3/4” polyester/polypropylene rope, 30 feet) 1202753 (5/8” polyester/polypropylene rope, 30 feet) 1202750 (3/4”...
- Página 2 12-mm diameter, polyester rope 1.0 APPLICATIONS 1.1 PURPOSE: Vertical lifelines and vertical lifeline subsystems are intended to be used as part of a personal fall arrest or restraint system. These lifelines and lifeline subsystems (with the exception of 3/8-inch wire rope) are not designed for use in horizontal lifeline systems. Applications include: Inspection work, construction, demolition, maintenance, oil production, confi...
-
Página 3: Applicable Standards
B. FREE FALL: Personal fall arrest systems used with these lifelines must be rigged to limit the free fall to 6 ft. (1.8 M) (according to ANSI Z359.1). Restraint systems must be rigged such that there is no possible vertical free fall. See subsystem manufacturer’s instructions for more information. -
Página 4: Making Connections
Connectors (hooks, carabiners, and D-rings) must be capable of supporting at least 5,000 lbs. (22kN). Connectors must be compatible with the anchorage or other system components. Do not use equipment that is not compatible. Non-compatible connectors may unintentionally disengage. See Figure 3. Connectors must be compatible in size, shape, and strength. Self locking snap hooks and carabiners are required by ANSI Z359.1 and OSHA. -
Página 5: Operation And Use
Per OSHA 1926.500 and 1910.66: Anchorages used for attachment of personal fall arrest systems shall be independent of any anchorage used to support or suspend platforms and capable of supporting at least 5,000 pounds (22.2 kN) per attached user; or, be designed, installed, and used as part of a complete PFAS which maintains a safety factor of at least two and is under the supervison of a qualifi... -
Página 6: Fall Clearance
E. FALL CLEARANCE: Ensure suffi cient clearance exists in your fall path to prevent striking an object during a fall. The clearance required is dependent upon the subsystem (rope grab and lanyard, rope grab and carabiner) and lifeline properties. Table 2 shows the approximate elongation for new DBI/SALA lifelines in dry conditions. - Página 7 splice must be made with fi ve tucks. Figure 7 - Spliced Eye Rope Terminations Connectors attached to wire rope lifelines must be attached using Synthetic Rope Termination a formed eye termination with a - five full tucks thimble. Acceptable methods of forming spliced eyes are: Spliced eye with one swaged ferrule;...
- Página 8 5.2 INSPECTION STEPS: Step 1. Inspect lifeline hardware (snap hooks, ferrules, thimbles, etc.). These items must not be damaged, broken or distorted. These items must be free of sharp edges, burrs, cracks, worn parts, or corrosion. Hook gates must move freely and lock upon closing. Step 2.
-
Página 9: Hardware Specifications
7.0 SPECIFICATIONS 7.1 LIFELINE SPECIFICATIONS: * The 12-mm diameter lifelines do not meet ANSI Z359.1 requirements. Table 3 - Lifeline Specivications Lifeline Material Tensile Strength 5/8” Diameter, Polyester/Polypropylene blend, 3-Strand Rope 7,000 lbs. (31.14 kN) 3/4” Diameter, Polyester/Polypropylene blend, 3-Strand Rope 8,820 lbs. - Página 10 9.0 LABELING The following labels must be present and fully legible: 9.1 ANSI Products:...
- Página 11 9.2 CSA Products:...
-
Página 12: Inspection And Maintenance Log
10.0 INSPECTION AND MAINTENANCE LOG SERIAL NUMBER: MODEL NUMBER: DATE PURCHASED: DATE OF FIRST USE: INSPECTION DATE INSPECTION ITEMS CORRECTIVE ACTION MAINTENANCE NOTED PERFORMED Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By:... - Página 13 10.0 INSPECTION AND MAINTENANCE LOG SERIAL NUMBER: MODEL NUMBER: DATE PURCHASED: DATE OF FIRST USE: INSPECTION DATE INSPECTION ITEMS CORRECTIVE ACTION MAINTENANCE NOTED PERFORMED Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By:...
- Página 14 This instruction applies to the following models: 1202702 1202772 1202842 1202903 1202974 1203133 1210015 1212400 5900163 6130029 1202703 1202773 1202842C 1202904 1202976 1203134 1210020 1212500 5900164 6130030 1202705 1202774 1202843 1202905 1202977 1203135 1210025 1212610 5900165 6130031 1202706 1202775 1202843C 1202906 1202978 1203136...
- Página 15 This instruction applies to the following models: 6130550 6140013 6140030 6140051 6140095 6140123 6140160 6140333 6140650 6141420 6130600 6140014 6140031 6140052 6140097 6140125 6140166 6140350 6140674 6141450 6130700 6140015 6140032 6140055 6140099 6140128 6140174 6140364 6140700 6141480 6130730 6140016 6140033 6140059 6140100 6140129...
- Página 16 LIMITED LIFETIME WARRANTY Warranty to End User: D B Industries, Inc., dba CAPITAL SAFETY USA (“CAPITAL SAFETY”) warrants to the original end user (“End User”) that its products are free from defects in materials and workmanship under normal use and service. This warranty extends for the lifetime of the product from the date the product is purchased by the End User, in new and unused condition, from a CAPITAL SAFETY authorized distributor.