Intermatic InTouch CA7100 Instrucciones De Instalación

_______________________________________________________________________
http://waterheatertimer.org/Intermatic-timers-and-manuals.html
Model CA7100
Master In-Wall Control Station
Specifications:
Wireless RF Control
Operating Temperature Range:
32°F (0°C) to 104°F (40°C)
Power Consumption: 4.0W Max
Backlit 128 x 64 Dot LCD Display
Ratings:
120VAC, 50/60Hz
Colors:
Includes white snap-on face plate.
Connections:
Black-Line, White-Neutral,
Green-Ground
RF Information:
Minimum Range:
50ft indoor; 100ft outdoor
Frequency: 908.42 MHz
Network Information:
Mesh Network - Each line powered
node acts as a repeater to route
distant signals.
Data Rate: 9600 bits/second
Size: 232 Z-Wave™ Nodes
INSTALLATION:
1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND
TEST THAT POWER IS OFF BEFORE WIRING.
2. Requires a 3-gang electrical junction box for installation.
3. Remove t he face plate. Using a finger or thumb nail, remove the face plate from the housing body by lifting
on the right edge by the menu navigation buttons. Remove exposed (3) screws to release mounting plate.
4. Attach mounting plate to 3-gang electrical junction box using (6) mounting screws furnished.
5. Refer to wiring diagrams for proper connection of master in-wall control station.
6. Check that all wire connections are secure and place all wires inside junction box.
7. Replace master in-wall control station using (3) mounting screws. Complete installation by snapping cover
plate back into place.
8. Reconnect your electrical power.
9. Operation: Press the "Enter" button to access setup menus. Press scene number button(s) to focus
control activities; Press "Enter" to toggle selected scene(s); Press
lighting level; Press the home key to clear selected scene(s).
10. For programming instructions refer to the
Face Color Conversion
The face color of this device can be converted to match interior design requirements.
1. Select and obtain the color of the face you desire.
2. The face plate has snaps on 3 sides. Using a finger or thumb nail, remove the face plate from the housing
body by lifting on the right edge by the menu navigation buttons.
3. Take the new face plate and position it properly to the housing body. Notice that the left edge has tabs that
must be inserted first. Press the plate into position.
4. The face plate snaps in with an audible click. Ensure that all snaps are secure.
The color conversion is complete.
FCC STATEMENT OF COMPLIANCE
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna or device.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
WARNING! Changes or modifications not expressly approved by Intermatic Inc. could void the user's authority to operate the
equipment.
The CA7100 Master In-Wall Control Station
frequency controller compatible with Z-wave™ enabled networks and
devices. Each line powered node in a Z-wave network is designed to
act as a repeater forming a mesh network eliminating radio "dead
spots" and providing the highest level of reliability.
Features
- Menu driven setup of scenes and events.
- Built-in astronomic timing with real-time-clock backup.
- Multiple location On/Off & Raise/Lower control when used with Z-
wave enabled switches and dimmers.
- Allows control of up to 100 individual pre-set scenes containing any
number of Z-wave enabled devices.
- Features 6 "Quick" pre-set scene activator buttons.
- Features individual scene status feedback for enhanced control.
- Separate focus and control buttons allows the user to custom mix
scene selections and vary light levels.
- Home key provides for quick de-selection of scenes and back-out
from menu programming.
WARNING: Read instructions completely before installation and retain
for future reference.
WARNING: For installation and/or use in accordance with appropriate
electrical codes and regulations.
WARNING: Consult a qualified electrician for installation and operation.
OTHER CAUTIONS:
1. For remote operation of Z-Wave compatible controls.
2. Use this device only with 75˚C rated copper or copper clad wire.
Note: Designed to work only in the presence of InTouch™
Server (CA5500B or other).
v
/
InTouch Installer & Users Guide
is an enhanced radio
w
to lower or raise selected scene(s)
(158CA12789).