Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATING YOUR FIXTURE
NOTE: Make sure you allow fixture to receive four full
days of sunlight before turning fixture ON.
1. Turn power switch ON.
2. Rotate the sensor assembly to reveal the time
adjustment knob. Rotate knob to "TEST", then
rotate sensor assembly back to desired sensing
direction. (Fig. 5).
NOTE: Fixture has a warm up period of about one
minute. Light will turn on during this period. Once the
light turns off, you are ready to test.
3. Walk across the detection zone at the farthest
distance you wish your sensor to detect motion.
Light will turn off 4 seconds after motion stops.
NOTE: Allow 5 seconds after light turns off before your
next test.
4. Note location of alignment mark on sensor assembly,
then rotate assembly to reveal the time adjustment
knob. Rotate knob to a duration up to 3 minutes, then rotate sensor
assembly back to desired sensing direction. Light will turn ON at night when motion is
detected and turn OFF at the selected time interval after motion stops.
NOTE: When battery is low, the fixture will automatically turn OFF. (The fixture will not turn ON
until the battery has recharged to the operating level.)
PROPER BATTERY CARE AND REPLACEMENT
NOTE: Proper care should ensure the longest possible life for your battery.
• Make sure that your solar panel is located in a sunny location.
• When battery is low, the fixture will automatically turn OFF. (The fixture will not turn ON until
the battery has recharged to the operating level.)
• To ensure proper recharge, turn power switch OFF and allow fixture to receive 4 full days of
sunlight before turning the fixture ON.
To replace the batteries:
1. Replacement batteries must be AA size Ni-MH, with
a capacity of 1800 mA-h. The use of any other type
or size will void your warranty.
2. Turn fixture OFF. Unplug fixture from solar panel
wire. While pressing in on the locking tab at the
bottom of the fixture, lift the fixture up to remove
from the mounting bracket.
3. Use the ribbon provided to gently remove the
batteries. Insert new batteries, being careful to
correctly orient the positive and negative terminals. (Fig. 6)
4. Reinstall the fixture to the mounting bracket, making sure the fixture snaps into the
locking tab. Plug the wire into the solar panel wire, pushing tightly until you hear
two clicks.
5. Prepare the fixture for operation according to the section titled "OPERATING YOUR
FIXTURE" in this instruction manual.
TROUBLESHOOTING
Problem
Cause / Solution
Light Does Not
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
Come On With
• Re-aim the head.
Motion At Night
• Relocate or reposition the unit away from the light source.
Fixture is not charging during the day.
• Solar panel must be connected to the connector extending
from the fixture housing when charging.
• Solar panel must receive direct sunlight to charge during
the day (reposition if shadowed).
• Solar panel must be clean and free from debris.
• Make sure batteries have been charged for 4 full days of
sunlight prior to turning the fixure ON.
• When battery is low, the fixture will automatically turn OFF until
the battery is charged to the operating level.
Light Comes On
There is motion in the detection zone.
For No Apparent
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
Reason At Night
TEST FOR YOURSELF.
• Cover the sensor lens with black electrical tape to prevent
sensor from detecting motion. If the light stays off, something in
the detection zone is triggering the sensor.
• Reposition the sensor.
* If the light stays on with the sensor lens covered, contact
customer service.
Fig. 5
Light Stays On At
A
Night And Does
Not Turn Off
Light Is On
During The Day
ON OFF
ONE YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Eaton warrants to customers that, for a period of one year from the date of purchase, Eaton
products will be free from defects in materials and workmanship. The obligation of Eaton
ON OFF
under this warranty is expressly limited to the provision of replacement products. This war-
ranty is extended only to the original purchaser of the product. A purchaser's receipt or other
proof of date of original purchase acceptable to Eaton. This is required before warranty per-
formance shall be rendered. This warranty does not apply to Eaton products that have been
altered or repaired that have been subjected to neglect, abuse, misuse or accident (including
shipping damages). This warranty does not apply to products not manufactured by Eaton
which have been supplied, installed, and/or used in conjunction with Eaton products. Damage
to the product caused by replacement bulbs or corrosion or discoloration of brass components
are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL EATON BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUEN-
TIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT
LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE
LIABILITY OF EATON FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH
THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
MODIFICATION OF EATON PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE,
Fig.6
EXCEED THE PURCHASE PRICE OF EATON PRODUCTS GIVING RISE TO A CLAIM. NO LABOR
CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact Eaton at 1-800-334-6871, press option 2 for
Customer Service, or via e-mail
ConsumerProducts@eaton.com and include the following information:
• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused. Eaton is not responsible for
merchandise damaged in transit. Repaired or replaced products shall be subject to the terms
of this warranty and are inspected when packed. Evident or concealed damage that is made
in transit should be reported at once to the carrier making the delivery and a claim filed with
them.
Reproductions of this document without prior written approval of Eaton are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at ConsumerProducts@eaton.com
Printed in China
2
There is motion in the detection zone.
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
• Reposition motion sensor.
* If the light continues to stay on, contact customer service.
The knob on the motion sensor is in the TEST mode.
• Rotate the knob to a duration up to 3 min.
The motion detector is shadowed.
• Reposition motion sensor.
Publicidad
