Wayfair Vanity Combo Instrucciones De Instalación

Installation Instructions for Vanity
TO ENSURE THAT YOUR INSTALLATION GOES SMOOTHLY,
PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO
STARTING.
WARNING & CAUTION: Failure to follow warnings and cautions could
result in serious injury. Do not exceed the maximum load capacity. Do not
stand on cabinet. Use cabinet on level ground.
STEP 1 | Vanity Installation
1. Fasten the vanity cabinet to the wall with 2 screws (not included) into wall studs through the back top rail or use toggle bolts if necessary.
2. Pulls are attached to the inside of the vanity. Re-attach so the pulls are visible from the outside of the doors.
STEP 2 | Full Extension Drawer Glide Removal
1. Open the drawer as far as possible.
2. Identify the plastic spring clips located in both slides.
3. At the same time, press the right slide spring clip downward and the left
slide spring clip upward (Fig.#3 & Fig.#4).
4. Once both spring clips are held in the indicated position, pull the drawer
straight out.
STEP 3 | Vanity Top Installation
1. Set the vanity top on top of the vanity base, checking the location of the p-trap and drain.
2. Remove the top and install the faucet per manufacturer's installation instructions.
3. Hand tighten the pop-up drain with a wrench. Be careful not to over-tighten the pop-up drain. Over tightening may cause cracks on the marble top.
4. Apply a thin bead of silicone compound around the vanity base and set the vanity top carefully in place. Remove any excess silicone compound with a wet rag.
5. Install the faucet, water lines and P-trap according to manufacturer's installation instructions.
STEP 4 | Full Extension Drawer Glide Installation
1. Close completely both slides attached to the vanity.
2. Move the component of the slides with ball bearings to the front of the slides, maintaining
the slides completely closed.
3. Carefully line up the slides of the drawer box with the slides in the base cabinet and close
the drawer all the way to the back.
4. Open the drawer completely to ensure it is properly installed.
STEP 5 | Hinge/Door Adjustment
The door alignment was set in the factory, but it could have shifted during transit. If
adjustment is needed, follow the instructions provided in the adjacent chart.
STEP 6 | Drawer Front Adjustment
1. Remove decorative hardware from the drawer front.
2. Hold drawer front in place and slightly loosen both alignment screws.
3. Move the drawer front left, right, up or down to desired position for alignment.
4. While holding the drawer front in place, tighten the alignment screws securely.
5. Install the decorative hardware to the outside of the drawer front.
MIRROR INSTALLATION
(If Included)
1. Determine the desired location of the mirror. Use appropriate screws or wall anchors (not included) to hang mirror.
2. Be sure the hanging hardware is rated to handle the weight of the mirror. The mirror weight is approximately 20 lbs.
CARE & MAINTENANCE
Vanity- To clean surface of doors or cabinet, use non-abrasive cleaners and or cleaning agents that do not contain solvents.
Vanity Top - Your vanity top will remain in its original state if you maintain and clean it properly. Clean the surface with a glass cleaner or other household cleansers that are non-abrasive. Using
abrasive cleansers will damage the surface.
Mirror - Use non-abrasive cleansers only.
For California Customers Only
WARNING: This product can expose you to chemicals including Wood Dust which is known to the State of California to cause cancer. For more information, go to
www.P65Warnings.ca.gov.
(If Applicable)
(If Applicable)
(If Applicable)
(If Applicable)
WARNING: Base cabinet supports a maximum weight of 200lbs. Exceeding
maximum weight limit will compromise the integrity of the cabinet structure
and could cause the cabinet to fail.
CAUTION: Do not hang from the cabinet.
right spring clip
left spring clip
Fig.#4
Fig.#3
Epoxy Drawer Glide Installation
1. In a 30º angle position, introduce the drawer in the base cabinet making
sure the drawer slide wheels are above the vanity slide wheels.
2. Close the drawer completely and to ensure it has been properly installed,
open it as far as possible.
Used to adjust
A
door height
A
CABINET FRONT VIEW
alignment
screws
Epoxy Drawer Glide Removal
(If Applicable)
1. Open the drawer as far as possible.
2. Lift the front part of the drawer to
reach a 30º angle position.
3. Pull the drawer straight out.
(If Applicable)
Used to adjust C Used to adjust between
B
gaps between doors door and cabinet
B
CABINET FRONT VIEW CABINET SIDE VIEW
alignment screws
drawer box
drawer front
decorative hardware
back top rail
C