Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Drill, Tin Snips, file
Fish wire (Provided)
Fastener Kit: 36486F
Wrenches: 10MM, 9/16", 11/16"
Drill Bits: 1/2"
Drilled Hole
Both sides
1
Qty. (2)
U-bolts – 3/8"-16
2
Qty. (4)
Conical Washer – 3/8"
3
Qty. (4)
Hex nut – 3/8"-16
4
Qty. (4)
Carriage Bolt – 7/16"-14 x 1.50" long
1.
Raise car on ramps, hoist, or jack stands.
2.
Remove 4 rubber exhaust isolators – 2 at the rear of the muffler and 2 near the rear differential. Spray lube helps with removal.
3.
Remove the heat shields by removing 6 nuts per shield with the 10mm wrench.
4.
Remove adhesive cover from over the access hole in frame. With a file open access hole to accept blocks.
5.
Trim heat shields as shown. Approx 7" long and 2-7/8" wide. Trim tip of rubber stand off (shown). Reinstall heat shield.
6.
Install U-bolts over muffler hanger brackets as shown.
7.
Raise hitch into position and install 3/8" hardware finger tight. Checking that the front hole in the bracket lines up with access hole.
8.
Using the hitch as a guide, drill 1/2" hole in car frame.
9.
Remove hitch. Paint bare metal and fish wire bolts and blocks thru access holes. Keep fish wires on bolts to ease hitch installation.
10.
While lifting hitch back into position thread fish wires thru the forward two mounting holes. Finish raising hitch into position and
install the 3/8" washer and nut on the U-bolt.
11.
With carriage bolts thru the mounting bracket remove the fish wires and install the washers and nuts.
12.
Tighten all fasteners.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008 Cequent Towing Products
Installation Instructions
Hyundai Genesis
Bumper
Drawbar Kit:
36065
Drawbar must be used in the
rise position only.
Frame
Existing Holes
5
Front Hole
1
3 2
5
6
7
Tighten all 3/8 fasteners with torque wrench to 30 Lb.-Ft. (41n*m)
Tighten all 7/16 fasteners with torque wrench to 50 Lb.-Ft. (68n*m)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
Muffler
4
Hanger
Bracket
6 7
Qty. (4)
Block – 1 x 2 x 3/16
Qty. (4)
Conical Washer – 7/16"
Qty. (4)
Hex nut – 7/16"-14
36486N
Part Numbers:
36486
90196
06659
1
32
Heat Shield
Forward
Rubber
Stand Off
10-7-08
Rev. A
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Towing Products 36065
Resumen de contenidos para Cequent Towing Products 36065
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 36486N 10-7-08 Rev. A 2008 Cequent Towing Products Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 36486N 10-7-08 Rev. A 2008 Cequent Towing Products Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 36486N 10-7-08 Rev. A 2008 Cequent Towing Products Form F206 Rev A 5605...