DIG R750 Manual De Instrucciones

Flowerbed Watering Kit
Model R750
Adjustable Flow Micro Sprayers
for watering borders, under canopies, and flowerbeds
INTRODUCTION
THANK YOU for purchasing the DIG model R750 Flowerbed Watering Kit. Please take
the time to read through the enclosed instructions and follow them step-by-step. If
you have any questions, please call our Technical Service department at
1-800-344-2281. Use the R750 Flowerbed Watering Kit to maximize the efficient use
of water in the landscape while promoting abundant growth in gardens. If the system
needs expansion, all the necessary parts are available individually.
STEP-BY-STEP INSTALLATION
Step 1: Connect the 3/4" FHT x MNPT backflow device to the faucet.
Step 2: Attach the #5 pressure regulator with FNPT
to the backflow device.
Option 1: To automate, first install
a battery-operated controller model
9001D or 7001 (not included), and
then connect the backflow device.
Option 2: To apply water-soluble fertilizer, or if you are
unsure of the water quality, we highly recommend using
#12 - 3/4" filter/fertilizer applicator. It will remove debris
that may otherwise clog the emitters and foggers. This
unit should be installed after the backflow device.
Step 3: Connect the #16 3/4" FNPT swivel adaptor to the pressure regulator,
and then connect the poly tubing by forcing the poly tubing into the swivel
adaptor while moving the poly tubing from side to side.
I N S T R U C T I O N
1
Step 4: Unroll the 1/2" poly tubing and lay it out in the area to be watered.
To increase pliability, leave in sun for a few minutes. Use # 60 stakes to
secure the poly tubing to the ground.
Step 5: Every 4', or any other spacing desired, punch holes in the poly tubing
by holding the poly tubing in one hand and the punch with the other. Apply just
enough pressure on the punch, while rotating it back and forth to create a hole
in one side of the poly tubing.
Step 6: Insert the barb end on the micro tubing into the 1/2" poly tubing.
Step 7: Cut the 1/4" micro tubing to the right length, then connect the #69
adjustable stakes with the sprayer to the 1/4" micro tubing. Note: Some
assembly may be required.
Step 8: Cut the micro tubing to the right length, then connect the
#101 adjustable full circle sprayer to the 1/4" micro tubing.
Step 9: Use the #19 1/2" tee to set up a three way layout of the 1/2" poly
tubing.
Step 10: Flush the line, and close the end of the poly tubing using #55
hose end. Turn the water on again and adjust the flow, and spray diameter on each
OPTIONAL
sprayer using the knob on the top of the stake.
Goof Plugs # 57
Use to plug holes in the 1/2" poly tubing or to close the end of the
1/4" micro tubing.
1/2" Stake holder # 60
Use to hold the 1/2" poly tubing to the ground.
Kit contains: 2-90° and 4-180° micro sprayers on adjustable flow stakes, 2-360° adjustable
flow sprayers, 50' of 1/2" poly tubing, 8-2' micro tubing with 1/4" barb, 1 backflow device, 1
pressure regulator, 1 swivel adaptor, 1-1/2" tee, 2-1/4" tees, 1 punch, 3-1/2" tubing holders,
2 hose ends, 2 plugs, and instruction manual.
M A N U A L
1210 Activity Drive
Vista, CA 92081-8510, USA
2
WARRANTY
DIG CORPORATION warrants these products to be free from defects in material and workmanship for
a period of three years from date of purchase. This warranty does not cover damage resulting from
accident, misuse, neglect, modification or improper installation. This warranty shall extend only to the
original purchaser of the product for use by the purchaser. The obligation of DIG CORPORATION under this
warranty is limited to repairing or replacing at its factory this product which shall be returned to the factory
within three years after the original purchase and which on examination is found to contain defects in
material and workmanship.
DIG CORPORATION SHALL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY KIND; THE SOLE OBLIGATION OF DIG BEING LIMITED TO REPAIR OR REPLACEMENT OF DEFECTIVE
PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Unattended use for prolonged periods without inspection to verify proper operation is beyond the
intended use of this product, and any damage resulting from such use shall not be the responsibility of
DIG CORPORATION. There are no warranties which extend beyond the description on the face hereof.
In the case of purchase of the product for use other than, for irrigation purposes, DIG CORPORATION
hereby disclaims any implied warranties including any warranties of merchantability and fitness for a
particular purpose. In the case of the purchase of the product for personal, family or household purposes,
DIG CORPORATION disclaims any such warranties to the extent permitted by law. To the extent that any
such disclaimer or implied warranties shall be ineffectual, then any implied warranties shall be limited in
duration to a period of three years from the date of the original purchase for use by the purchaser. Some
states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply
to you.
In order to obtain performance under this warranty, the unit must be returned to the factory, along with
proof of purchase indicating original date of purchase, shipping prepaid, addressed as follows:
DIG CORPORATION, 1210 Activity Drive, Vista, CA 92081-8510. Repaired or replaced units will be shipped
prepaid to the name and address supplied with the unit returned under warranty. Allow four weeks for
repairs and shipping time. Repair of damaged units not otherwise within warranty may be refused or done
at a reasonable cost or charge at the option of DIG CORPORATION.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
CUSTOMER SERVICE: 1-800-344-2281 FAX: 760-727-0282
www.digcorp.com
e-mail: dig@digcorp.com
26-006 Rev A 042213
Printed in the USA
3