Publicidad
Idiomas disponibles
Idiomas disponibles
The color-coded rings of receptacles and connectors
include a cap. The color-coded rings of plugs and
inlets do not include a cap.
Color-coded ring on plug side
Cap with color-coded ring on receptacle side
Rated current and voltage markings
It is essential to indicate the current and voltage of
the main circuit on the supplied stickers. Apply the
stickers on or adjacent to the product so they can
easily be seen.
OPERATION
To ensure safe and reliable operation,
MELTRIC plugs and receptacles must be used
in accordance with their assigned ratings.
They can only be used in conjunction with mating
WARNING
receptacles or plugs manufactured by MELTRIC or
another licensed producer of products bearing
DANGER
the
™ technology trademark.
CAUTION
Connection
NOTICE
First check to see that the power source is
de-energized. DO NOT ENGAGE ON AN
ADVERTENCIA
ENERGIZED CIRCUIT.
DANGER
WARNING
Orient the plug so the contact will fit into the recepta-
cle figure 1 . Push the plug partially into the recepta-
DANGER
cle and rotate the plug counterclockwise until it hits a
CAUTION
stop figure 2 . Then insert plug fully into receptacle
and rotate clockwise about one quarter turn until the
CAUTION
AVISO
locking pin engages into the slot on the receptacle
figure 3 .
NOTICE
ADVERTENCIA
DANGER
CAUTION
AVISO
Insert
Twist until
pin locks
Disconnection
First check to see that the power source is
de-energized. DO NOT DISCONNECT ON
AN ENERGIZED CIRCUIT.
WARNING
Insert unlocking key onto locking pin as shown in
figure 4 . Disengage locking pin by sliding unlocking
DANGER
key as shown in figure 5 . When locking pin is re-
leased, hold unlocking key in position and twist plug
counterclockwise about 30° as shown in
CAUTION
figure 6 . After turning, withdraw plug.
NOTICE
ADVERTENCIA
DANGER
CAUTION
AVISO
1
PADLOCKING OPTION
Assembly
Place the locking ring as shown:
Watertightness
gasket
2
Twist then
insert
Operation
Connect the product equipped with the locking ring,
insert the shaft and padlock it.
3
Insert un-
lock tool
4
5
Retract
locking
pin
6
Twist &
Remove
Lug
Locking ring
Color-coded ring
MAINTENANCE
Before inspecting, repairing,
WARNING
or maintaining MELTRIC
products,disconnect electrical
DANGER
power to the receptacle to eliminate the risk of elec-
trical shock.
CAUTION
MELTRIC products require little on-going mainte-
NOTICE
nance. However, it is a good practice to periodically
perform the following general inspections:
ADVERTENCIA
• Check the mounting screws for tightness.
DANGER
• Verify that the weight of the cable is supported
by the strain relief mechanism and not by the ter-
CAUTION
minal connections.
AVISO
• Check the IP gaskets for wear and resiliency.
Replace as required.
• Verify the electrical continuity of the ground circuit.
• Check the contact surfaces for cleanliness
and pitting.
Deposits of dust or similar foreign materials can be
rubbed off the contacts with a clean cloth. Sprays
should not be used, as they tend to collect dirt. If
any significant pitting of the contacts or other serious
damage is observed, the device should be replaced.
Receptacle contacts may be inspected by a qualified
electrician. This should only be done with the power off.
MANUFACTURER'S RESPONSIBILITY
MELTRIC's responsibility is strictly limited to the
repair or replacement of any product that does not
conform to the warranty specified in the purchase
contract. MELTRIC shall not be liable for any pen-
alties or consequential damages associated with the
loss of production, work, profit or any financial loss
incurred by the customer.
MELTRIC Corporation shall not be held liable when
its products are used in conjunction with products not
™ technology trademark. The
bearing the
use of MELTRIC products in conjunction with mating
devices that are not marked with the
technology trademark shall void all warranties on
the product.
MELTRIC Corporation is an ISO 9001 certified com-
pany. Its products are designed, manufactured and
rated in accordance with applicable UL, CSA and IEC
standards. MELTRIC designs and manufactures its
products in accordance with Marechal keying standards
established to ensure intermateablility with similarly
rated products manufactured by Marechal Electric
Group.
™
INSCS1000 F
Publicidad
