Publicidad
May we congratulate you on your new greenhouse
GB
Dear Customer!
DEAR CUSTOMER
Congratulations on purchasing your new
The assembly of your new house requires
greenhouse. It is important that you follow these
a bit of technical knowledge. However, it is
assembly instructions step-by-step.
important that the assembly instructions are
followed strict-ly. The assembly instruction
The assembly instructions are a combination of text
is a combination of text and illustrations. The
and illustrations. The profiles are packed in separate,
profiles are packed in separate numbered packs
numbered packs corresponding to their order of use
in the instructions. Assemble one pack at a time.
corresponding to the order in the assembly
All nuts, bolts and fittings are contained in bag No.
instruction. Erect one pack at a time. All nuts
0 (specified on page 12). Each pack is specified in
and bolts and fittings are found in bag No. 0
separate lists of components.
(specified on page 12). Each pack is specified in
All detailed illustrations are marked with the
separate lists of components.
following symbols:
All detailed illustrations are marked with
symbols:
Seen from the inside
Seen from the outside
Seen from inside
Seen from outside.
SOME SAFETY PRECAUTIONS
•
Assembly must only be carried out in dry and
calm weather.
Precautions.
•
Always wear work gloves when installing the
•
Assembly must only be carried out in dry
glazing. Greenhouse glass has sharp edges,
and calm weather.
especially if it breaks.
•
Always use working gloves while glazing.
•
Assistants and especially children must be
Greenhouse glass has sharp edges,
warned that broken glass is dangerous. Pick
especially if the glass breaks.
up all broken glass at once and remove it with
•
Assistants and especially children must be
care.
•
We recommend that you wear protective
warned that broken glass is an element of
glasses while fixing the spring wire clips.
danger. Pick up broken glass at once and
•
Any ladders that are used must be placed on a
remove it with care.
level surface.
•
We recommend to use protective glasses
•
It is essential to have an assistant available.
while fixing the spring wire clips.
•
Place the ladder on a level support.
PAGE 12: TOOLS
•
It is essential to have an assistant.
Assembling the greenhouse requires the tools
shown on page 12.
References
PAGE 13: FOUNDATIONS
The column marked
indicates the
No base is included with this product. However, an
page(s) on which the component is used.
original base is available separately. This base is easy
to construct and will guarantee you a stable base for
Page 13:
your greenhouse.
Foundation
If you construct your own base, the specified
The base is not included in this delivery.
measurements must be external measurements.
However, an original base can be bought
If you purchase an original base, you will also require
about 75 litres of concrete and six to eight plastic/
separately. It ensures you a stable and easy to
concrete pipes of about 800mm. These pipes, which
build base.
must be buried at a sufficient depth to ensure that
If you make your own base the measurements
they do not freeze, secure the corner and middle
indicated must be external measurements.
anchors.
If you buy an original base you furthermore
The base must be completely level and square;
need about 75 litres of concrete and 6/8
the latter can be ensured by checking that the two
plastic-/concrete pipes of about 800 mm which
diagonal measurements are equal.
are placed in a non-freezing depth for the
ATTACHMENT TO THE BASE
fastening of the corner and middle anchors.
If you construct your own base, you must drill holes
The base must be 100% level and square; the
(7mm) in the ground frame between all the vertical
latter is ensured by checking that the two
profiles. The greenhouse must then be secured to
diagonal measurements are equal.
the base using screws (A).
If you use an original base, the greenhouse must be
Tools
secured to each vertical bar as shown on drawings
The mounting of the greenhouse requires the
B/C.
tools shown on page 12.
PAGE 14-27: ORDER OF ASSEMBLY
Place the components as shown on the illustration
Page 14-27:
and assemble in the order shown in the pictures. Do
Place the components as shown on the
not tighten the nuts fully until the entire sub-frame
illustration and assemble in the order shown
has been assembled.
in the pictures. Do not tighten the nuts
completely until the front gable construction
PAGE 24-27: DOORS AND WINDOWS
has been assembled.
For easier assembly, we recommend that you oil the
screws for the doors. The glass or polycarbonate for
the door(s) and windows must be fitted at the same
time as the profiles.
PAGES 30-37: FITTING OF GLASS/
Page 13:
POLYCARBONATE
(Fastening to the base).
Important before assembly!
When constructing your own base you have
Make sure that the gables and sides are level
to drill holes (7 mm) in the ground frame
and square and that door(s) and window(s) are
between all the vertical frames, the greenhouse
functioning perfectly.
is then fastened to the base with screws (A).
Using an original base the greenhouse is
The best order of assembly for the glass or
fastened to each vertical bar as shown on
polycarbonate is as follows:
Windows - Roof - Doors - Gables - Sides
drawing B/C.
PAGE 30-33: GLASS INSTALLATION
Page 24-27:
Glass installation (illustrations 1 to 8)
For an easier assembly we recommend that you
Degrease the sheets and frames with spirit.
oil the screws for the doors.
Start glazing from the bottom, one pane at a time.
Apply a 3mm silicone bead around the vertical
Fitting of glass/polycarbonate
frames as indicated (the dotted lines on the
Important before glazing!
illustration). (A 3mm bead of silicone is sufficient to
ensure maximum adhesion). If you use more silicone
than recommended, extra tubes can be purchased.
Make sure that gables and sides are level and
square, and that door(s) and window(s) are
Spring wire clips and glass-holders must be fitted as
functioning perfectly.
shown.
X = Spring wire clips, > = Glass-holders
Best order of assembly:
1) Windows – 2) Roof – 3) Doors – 4) Gables
If you accidentally break a pane, carefully pull the
– 5) Sides
broken glass outwards and loosen the silicone using
a sharp craft knife.
Clean the profile completely before inserting a new
Page 30-33:
pane of glass.
Glazing (illustration 1 to 8)
Degrease the sheets and frames with spirit.
PAGE 34-37: POLYCARBONATE INSTALLATION
Start glazing from below, one glass at a time.
The illustrations at the bottom of pages 34/36 show
Apply a 3 mm silicone line on the vertical
where to fit the polycarbonate sheets and strips. The
frames where indicated (dotted lines on
type designation states the length in millimetres. If
the illustration). (A 3 mm line of silicone is
adjustment is necessary, use a fine-tooth saw.
NB! To avoid the growth of algae, prevent the
sufficient to obtain maximum attachment). If
polycarbonate sheets from coming into contact with
you do use more than recommended, you can
the ground by resting them on a sheet of cardboard.
buy extra tubes.
A-strips are fitted as shown on pages 35/37. Insert
Spring wire clips and glassholders are to be
the sheet into the bottom strip, bend the sheet
fitted as shown.
slightly outwards and insert it into the top strip.
X = Spring wire clips, > = Glassholders
M-strips are fitted as shown on pages 35/37. Place
In case of broken glass carefully pull it
the upper part of the strip under the aluminium
profile along the full length of the sheet and then
outwards and loosen the silicone by means of a
click the strip into position from above.
sharp craft knife.
Clean the profile completely before inserting a
new pane of glass.
U-strips are fitted as shown on pages 35/37.
Fit the strip to the sheet and adjust the length.
Page 34-37:
Mounting of polycarbonate
If desired, the sheets may be sealed against insects.
Seal the top using aluminium tape or silicone. The
The illustrations at the bottom of page 34/36
bottom should only be sealed with air-strip tape to
show where to mount the polycarbonate plates
allow condensation to escape (available from your
and lists. The type indication states the length
local dealer).
in mm. A possible adjustment is made by
means of a fine-tooth saw.
Your greenhouse is now fully assembled. However,
NB! To avoid the formation of algae the
please note the following:
polycarbonate sheets must not come into
contact with the ground. Rest them on a piece
MAINTENANCE
•
of cardboard.
Grease the doors (hinges and locks).
•
Keep the gutters free from leaves, etc.
•
Adjust the windows as necessary.
A-lists are mounted as shown on page 35/37.
•
Replace any broken glass.
Put the sheet into the bottom list, bend the
•
Clean the greenhouse with disinfectant before
sheet slightly outwards and put it in the top list.
and after the growing season.
M-lists are mounted as shown on page 35/37.
WINTER PROTECTION
Place the upper part of the list under the alu.
If you anticipate snow during the winter, we
profile in the whole length of the sheet and
recommend the following winter precautions:
•
Support the apex of the roof in the middle.
hereafter click on the list from above.
•
Remove any deep snow from the roof.
•
Take precautions to prevent snow falling from
B
a tree or roof, for example.
Sealing of the polycarbonate sheets
•
Remove the cylinders for the automatic
The sheets may be sealed against insects.
window openers, if fitted (optional extras).
Close the top end off with alu-tape or silicone.
•
Secure the door(s) and window(s) to prevent
The bottom only with airstrip tape to let
wind damage to the greenhouse.
condensation out (available at your local
dealer).
WATER AND CONDENSATION
Please note that your greenhouse is not like a
conservatory, for example, and that you should
Now your greenhouse is completely assembled.
therefore be aware that the greenhouse may leak
However, please notice the following:
during or after precipitation and that condensation
will occur on the inside of the greenhouse. Good
Maintenance
ventilation will help prevent condensation.
•
Grease doors (hinges and lock).
•
Clean the gutter for leaves, etc.
INSURANCE
•
Adjustment of windows.
Please note that not all insurance companies cover
•
Replacement of broken glass.
greenhouses automatically. Please contact your
insurance company to ensure that your greenhouse
•
Clean the house with disinfectant before
is covered.
and after the growing season.
GUARANTEE
Winter Protection
Juliana greenhouses are covered by a 12-year
In areas with occurrence of snow we
guarantee, which covers the replacement or repair
recommend the following winter protection:
of faulty parts. The guarantee does not cover
•
Support the roof ridge at the centre of the
polycarbonate, glass, transport, assembly, freight,
house.
etc.
Juliana greenhouses are covered by a two-year
•
Remove greater snow loads from the roof.
warranty on painted parts, where fitted. Note that
•
Take precautions against snow falling
marks on the paint may occur due to suspension of
down from for instance a tree or a roof.
the profiles.
•
Dismount the cylinders for the automatic
The guarantee will be void if the greenhouse is not
window openers, if any (optional extras).
assembled in accordance with these instructions.
•
Secure door(s) and window(s) preventing
wind damage to the house.
COMPLAINTS
All our greenhouses are built to the highest quality
standards. However, should you experience any
Insurance
problems, please contact your dealer at once. When
Please note that not all insurance companies
describing the defect, please state the greenhouse
cover glasshouses automatically. Please
model, the component number and the quality
contact your insurance company to ensure an
control number.
insurance coverage.
Congratulations on your new greenhouse, which we
Guarantee
hope will bring you a lot of pleasure for many years
Juliana grants a guarantee of 12 years which
to come.
covers replacement of faulty parts. The
Yours sincerely,
guarantee does not cover polycarbonate, glass,
transport, assembly, freight etc.
Juliana Drivhuse A/S
Juliana grants a guarantee of 2 years on painted
parts, if any. Note that marks in the painting
may occur due to suspension of the profiles.
The guarantee is invalid if the greenhouse is
not assembled according to these instructions.
Complaints
All our greenhouses are built to high standards
of quality. However, should a complaint
occur please contact your dealer at once.
Remember to specify the defect by indicating
the greenhouse model and number of the
component and the quality control number.
USA
Publicidad
