Silver Eagle SE288 Instrucciones De Operación página 2

SE288 TWO-IN-ONE 8MM Punch/Flange Tool
FAILURE TO OBSERVE THESE WARNINGS COULD RESULT IN INJURY
THIS INSTRUCTION
IMPORTANT SAFETY INFORMATION.
READ THIS INSTRUCTION MANUAL CAREFULLY
AND UNDERSTAND ALL INFORMATION BEFORE
OPERATING THIS TOOL.
• It is the responsibility of the owner to make sure all
personnel read this manual prior to using the device. It
is also the responsibility of the device owner to keep
this manual intact and in a convenient location for all to
see and read. If the manual or product labels are lost or
not legible, contact Matco Tools for replacements.
If the operator is not fluent in English,
the product and safety instructions shall be read and
discussed with the operator in the operator's native
language by the purchaser/owner or his designee,
making sure that the operator comprehends its contents.
• Always operate, inspect and maintain this tool in
accordance with American National Standards Institute
Safety Code of Portable Air Tools (ANSI B186.1) and any
other applicable safety codes and regulations.
• For safety, top performance and maximum durability of
parts, operate this tool at 90 psig; 6.2 bar max air
pressure with 3/8" diameter air supply hose.
• Always wear safety goggles (users & bystanders)
• Always wear hearing protection (users & bystanders)
when using this tool. High sound levels can cause
permanent
protection as recommended by your employer or OSHA
regulation.
• Keep the tool in efficient operating condition.
• Operators and maintenance personnel must be
physically able to handle the bulk, weight and power of
this tool.
• Air powered tools can vibrate in use. Vibration, repetitive
motions or uncomfortable positions over extended
periods of time may be harmful to your hands and arms.
Discontinue use of tool if discomfort, tingling feeling or
pain occurs. Seek medical advice before resuming use.
• Air under pressure can cause severe injury. Never direct
air at yourself or others. Always turn off the air supply,
drain hose of air pressure and detach tool from air supply
before installing, removing or adjusting any accessory
on this tool, or before performing any maintenance on
this tool. Failure to do so could result in injury. Whip
hoses can cause serious injury. Always check for
damaged, frayed or loose hoses and fittings, and replace
immediately. Do not use quick detach couplings at tool.
See instructions for correct set-up.
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Place the tool on the work be f ore start i ng the tool. Do
not point or in d ulge in any horse p lay with this tool.
• Keep body working stance balanced and firm. Do
not overreach when operating the tool.
Always wear heavy-duty leather gloves when
•
handling sheet metal. Sharp edges can cause
severe injury.
SE288
WARNING
MANUAL CONTAINS
hearing loss. Use
• Keep tool out of reach of children.
• Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
After disconnecting the Punch/Flange Tool
•
from the air supply, there could still be enough air
pressure to fire the Punch/Flange Tool. After
making sure the air supply is disconnected,
ALWAYS fire the Punch/Flange repeatedly to
make sure all air is bled from the tool.
• Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer
• Ensure the work piece is securely fixed.
• Never use dull, chipped or damaged accessories.
• Never cool a hot accessory in water as brittleness
and early failure can result. Accessory breakage
or tool damage may result from prying.Take
smaller bites to avoid getting stuck.
• Do not lock, tape or wire the tool valve in the "on/off"
position.
• Avoid direct contact with accessories during and
after use. Operation can cause impacts, cuts,
abrasions & heat. Gloves will reduce the risk of cuts or
hearing
burns.
• Keep away from punch/flange end of tool. Do not wear
jewelry or loose clothing. Secure long hair. Scalping
can occur if hair is not kept away from tool and
accessories. Choking can occur if neckwear is not
kept away from tool and accessories.
• Do not lu b ri c ate tools with flam m a b le or vol a t ile liq u ids
such as ker o s ene, die s el or jet fuel.
• This tool is not insulated against electric shock.
• This tool must not be used in explosive atmospheres.
• Use accessories only recommended by Matco Tools.
• Servicing and repairs should only be made by
authorized service center.
• Do not force tool beyond its rated capacity.
• Do not use (or modify) the tool for any other purpose
than that for which it was designed without consulting
the manufacturer's authorized representative.
• Do not remove any labels. Replace damaged labels.
• This product may contain one or more chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands
thoroughly after handling.
• Handling the brass parts of this product will expose
you to lead, a chemical known to the S tate of California
to cause birth defects a nd other reproductive harm.
Wash hands after handling.
2 Revised 10/06/15