Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24919F
Wrenches: 11/16, 9/16, 8mm
Drill Bits: N/A
AREA TO BE
Figure 3
TRIMMED
Figure 1
FRAME
ACCESS HOLE
KINK BOLT LEADER
TO KEEP BLOCK
INDEPENDENT OF BOLT
EXAMPLE OF FISHWIRE PROCEDURE
j
Qty. (4)
Carriage bolt 7/16-14 X 1.75 GR5
k
Spacer 1.00" X 3.00" X .250 Carriage Block
Qty. (4)
l
Conical washer 7/16"
Qty. (4)
p
Flat Washer 5/16"
Qty. (6)
1.
Remove bolts and plastic covers from underside of vehicle using and 8mm socket. (Both sides)
2.
Remove square rubber plugs from the underside of frame rails. (Both sides)
3.
Using square access hole and supplied bolt leader, insert 7/16" bolt and spacer block into frame as show in figure 1.
4.
Raise driver side bracket into place, attach conical washers and 7/16" nuts, finger tighten.
5.
Raise hitch into position , attach conical washers and 7/16" nuts, finger tighten.
6.
Install 3/8" bolts, (with bolt heads facing toward tailpipe) with flatwashers and locknuts through holes in driver side bracket and mating holes in the hitch.
7.
Torque all hardware to torque specification below.
8.
Reinstall square plug removed from frame rail
9.
Reinstall plastic covers. On single exhaust vehicles the plastic cover on the passenger side will need to be trimmed before reinstalling. (Figure 3)
Tighten all fasteners with torque wrench: 7/16-14 GR5 to 50 Lb.-Ft. (68 N*M),
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and
exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut
access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©
2014, 2015 Cequent Performance Products, Inc – Printed In Mexico
Installation Instructions
Rearward
Single exhaust models require
Fascia
underbody shield trimming
Drawbar must be used in the
RISE position only.
n
DESIRED BOLT
ATTACHEMENT HOLE
3/16-16 GR5 to 30 Lb-ft. (41 N*M)
Chrysler 200
Drawbar Kit:
3593
(Sold separately)
Access hole for
hardware
m
Qty. (4)
NUT 7/16-14
n
Qty. (4)
7/16 Bolt Leader (Wireform)
o
Qty. (3)
Bolt 3/8-16 X 1.50 GR5
q
Qty. (3)
Locknut Hex. 3/8-16
Sheet 1 of 3
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
24919N
10-05-15
Form: F205 Rev A 5-6-05
24919
60352
77306
24481 UH
Figure 2
Rev. C
Publicidad
Manuales relacionados para Cequent Performance Products 24919
Resumen de contenidos para Cequent Performance Products 24919
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 © 2014, 2015 Cequent Performance Products, Inc – Printed In Mexico 24919N 10-05-15 Rev.
- Página 2 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. Hoja 2 de 3 © 2014, 2015 Cequent Performance Products, Inc – Printed In Mexico 24919N 10-05-15 Rev.
- Página 3 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systè mes d’attelage. © 2014, 2015 Cequent Performance Products, Inc – Printed In Mexico Feuille 3 de 3...