Grinding Tool Safety - Silverline 123339 Manual Del Usuario

123339
Mains Electrical Tool Safety
• The wires in this product are coloured:
Blue Neutral (N)
Brown Live (L)
Green & Yellow Earth (E)
• As the colours may not correspond with the coloured markings in your
plug, proceed as follows.
• The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black, the wire which
is coloured brown must be connected to the terminal which is marked
L or coloured red.
• This appliance must be protected by a suitable fuse.
• To prevent fire or shock hazard, do not expose this product to rain /
water or moisture.
• There are no user serviceable parts inside except those referred to in this
manual. Always refer servicing to qualified service personnel. Never
remove any part of the casing unless qualified to do so; this unit contains
dangerous voltages.
• Use of a residual current device (RCD) will reduce the risk of
electric shock.
NEVER CONNECT THE BROWN OR BLUE WIRE TO THE EARTH PIN OF THE
13 AMP PLUG. IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN
Dangerous environment
• Do not use power tools in damp or wet conditions, or expose them
to rain. Provide adequate surrounding work space and keep area well
lit. Do not use power tools where there is a risk of explosion or fire from
combustible material, flammable liquids, flammable gasses, or dust of an
explosive nature. When using power tools avoid contact with any earthed
items such as pipes, radiators, cookers, refrigerators, metal baths
and taps.
Protect yourself from vibration
• Hand held power tools may produce vibration. Vibration can cause
disease. Gloves to keep the operator warm may help to maintain good
blood circulation in the fingers. Hand held tools should not be used for
long periods without a break.
Maintain your power tool
• Ensure all ventilation holes are kept clear at all times. Overheating and
fire may otherwise result.
Always disconnect
• Before changing fittings or accessories, always ensure that your tool is
disconnected from the power source.
Switch off before connecting
• Ensure that the power tool is switched off before connecting to the power
source. If the power tool stops unexpectedly, turn the power switch to off.
115mm Angle Grinder
Do not abuse the power cord
• Be sure your cable / extension cable is in good condition. Always have
a damaged cable / extension cable replaced at an authorised service
centre before using it. Never yank or pull the cable to disconnect it from
the power socket. Never carry your tool by its cable. Keep the cable away
from damp, heat, oil, solvents, and sharp edges.
Don't leave the tool running unattended
• Always wait until your tool has completely stopped functioning, and has
been unplugged, before leaving it.

Grinding Tool Safety

• Always wear appropriate personal protective equipment. When
using a grinder, safety goggles, ear defenders, and dust masks should
all be worn.
• Do not attempt to cut, or grind, magnesium, or any alloy that has a high
magnesium content.
• Only use discs of the size specified in this instruction manual. Attempting
to use any unsuitable accessory, or attachment is extremely dangerous,
and could lead to serious injury.
• The maximum speed of the cutting / grinding disc should always
be higher that the maximum speed of the machine to which they will
be attached.
• Use the correct cutting / grinding disc for the job. Stone and metal
working discs are not interchangeable. Cutting and grinding discs are
also not interchangeable.
• Do not allow discs to become wet, or oil soaked. If you suspect that
a disc has degraded in storage DO NOT USE.
• Inspect cutting / grinding discs before use. If a disc is damaged in any
way (chipped, fractured, etc) DO NOT USE. Dispose of disc and replace.
Damaged discs can spontaneously shatter.
• Read and understand all information supplied with cutting / grinding
discs. Do not use discs that have passed their expiry date.
• Do not attempt to make cuts that exceed the maximum cutting depth
of the disc.
• Do not use any form of spacers to make an incorrect disc fit
your machine.
• Ensure that the cutting / grinding disc is fitted correctly and securely
before use. Run the machine with the disc fitted, but no load, for 30
seconds before attempting to cut / grind. If excessive vibration is
encountered, stop the machine and correct the cause before use.
• Never operate a grinder without its guards in place, cutting / grinding
discs can spontaneously shatter. Failure of an unprotected disc can result
in severe injury to yourself or others around you.
• Do not stand in line with the cutting / grinding disc when in use.
• Do not operate the spindle lock while the grinder is running.
• Allow the machine to maintain a good operating speed, do not force the
machine to stall or slow by using excessive pressure.
• Be aware that machine will "run on" for some time after being switched
off. Allow the machine to stop itself. Do not stop the machine by holding
the disc against any object. NEVER place grinder down until the disc has
completely stopped.
• As a grinding disc is used, it will wear, and reduce in size. If the disc
becomes too small to work with easily, replace it.
www.silverlinetools.com
5