PestWest Chameleon 1x2IP Instrucciones De Uso página 3

REPLACEMENT PARTS
TUBE: 15 WQUANTUM BL SHATTERPROOF
130-000171
GLUE BOARD: 135-000048
STARTER: SERIES STARTER - Philips S2 or
Sylvania type FS22
Universal 240v starters are unsuitable and may cause
unreliable starting of the unit.
Only use genuine PestWest replacement parts to ensure
high efficiency. Use of non-approved parts may void the
guarantee.
CHANGING THE TUBES
Remove the catch tray by pulling out and holding
the spring-loaded silver knob on the side of the tray.
QUANTUM BL SHATTERPROOF
F15T8BL350SH
Open the guard; this pivots downwards from its lower
edge. Unclip the top of the guard from the body by
VABB427
pushing it upwards which will allow it to be hinged
SERIES STARTER - PhilipsS2 or
forward on the lower pivot points. This will permit
Sylvania typeFS22.
access to the tubes and starters.
Universal 240v starters are unsuitable
Grasp the tube with one hand and unscrew the white
and may cause unreliable starting of the
waterproof cap anticlockwise with the other hand
unit.
until it slides free from the lamp holder. Repeat this
operation with the waterproof cap at the other end of
the tube.
Care should be taken when removing each waterproof
cap to ensure that its rear red rubber water-sealing ring
does not become displaced and remains on the lamp
holder body. Should this occur, it must be removed
and refitted into the annular ring on the back of the
waterproof cap before the cap is screwed back onto the
lamp holder.
With the waterproof caps removed the tube may now
be removed by withdrawing it away from the unit.
Repeat the operation with the other tube.
PestWest's Chameleon 1x2 IP unit is fitted with the
revolutionary new Reflectobakt® sleeves, a PestWest
innovation introduced to improve the performance
of the units. The Reflectobakt® sleeve is a screen
positioned between the source of the UV light and
the sticky board, reducing the amount of UV striking
®
sleeves, a PestWest innovation introduced to
the board, and significantly increasing the life of the
adhesive.
Unclip the Reflectobakt® sleeves from the used
tubes and fit them onto the new tubes following
the instructions described under – FITTING THE
REFLECTOBAKT® SLEEVE.
Position the waterproof caps on the new tubes, fitted
with Reflectobakt® sleeve, refit into the lamp holders
by pushing the tubes into place. Refit each waterproof
cap in turn whilst holding the tube down in position
with one hand to avoid it springing out of place whilst
the caps are being tightened. The caps should be fully
screwed down to ensure a watertight seal with the
tube.
Check that the Reflectobakt® sleeves are correctly
placed, shielding the glue board from the light emitted
Unclip the Reflectobakt
by the tubes thus maintaining its effectiveness. Ensure
onto the new tubes following the instructions described under –
FITTING THE REFLECTOBAKT
the Reflectobakt® is positioned at an equal distance
from each end of the tube.
Position the waterproof caps on the new tubes, fitted with
®
Reflectobakt sleeve, refit into the lamp holders by pushing the
tubes into place. Refit each waterproof cap in turn whilst holding the
FITTING THE REFLECTOBAKT® SLEEVE Take the tube and
tube down in position with one hand to avoid it springing out of
line up the two leading edges of the Reflectobakt®
place whilst the caps are being tightened. The caps should be fully
screwed down to ensure a watertight seal with the tube.
sleeve with the pairs of pins at either end of the tube
Check that the Reflectobakt
- see Fig 1. Ensure that the sleeve is fitted centrally to
the glue board from the light emitted by the tubes thus maintaining
its effectiveness. Ensure the Reflectobakt
the tube so that the small gap between the end of the
distance from each end of the tube.
sleeve and the metal end of the tube is the same at both
FITTING THE REFLECTOBAKT® SLEEVE Take the tube and line
ends. Carefully push the sleeve so it is in contact along
up the two leading edges of the Reflectobakt
the length of the tube surface. It should grip and stay in
of pins at either end of the tube - see Fig 1. Ensure that the sleeve
position. Re-fit the tube into the unit; the sleeve should
is fitted centrally to the tube so that the small gap between the end
of the sleeve and the metal end of the tube is the same at both
be positioned at the back of the tube, keeping the light
ends. Carefully push the sleeve so it is in contact along the length
off the sticky board. At all times, handle the shield with
of the tube surface. It should grip and stay in position. Re-fit the
tube into the unit; the sleeve should be positioned at the back of the
care, as the dimensions are critical in order that it fits
tube, keeping the light off the sticky board. At all times, handle the
the tube properly.
shield with care, as the dimensions are critical in order that it fits the
tube properly.
Method of assembling Reflectobakt® showing
Method of assembling Reflectobakt
alignment in relation to pins:
relation to pins:
Fig 1
Fig 1
STARTER REPLACEMENT (if necessary). Should be replaced
every time tubes are changed. This operation ismost
STARTER REPLACEMENT (if necessary).
easilyaccomplished when the upper tube is removed.To gain
access to the starters the white waterproof caps located on Should be replaced every time tubes are changed.
thelower surface of the chassis tray need to be removed. If they
This operation is most easily accomplished when the
have previously been tightened using toolsthe use ofa pair of
upper tube is removed. To gain access to the starters
electricians'pliers will enable this task to be more easily
accomplished. To access the caps, first remove the catch tray and
the white waterproof caps located on the lower surface
drop the front guard down (follow the procedure described under
of the chassis tray need to be removed. If they have
CHANGING THE TUBES). Unscrew one cap by turning it
anticlockwise. Remove the starter from its housing by turning it
previously been tightened using tools the use of a pair
anticlockwise, then extracting it downwards. Repeat the same
of electricians' pliers will enable this task to be more
operation with the other starter. Fit the new starters following the
easily accomplished. To access the caps, first remove
above procedure in reverse order. Take great care that the
blacksealing gasket ring located on the starter cap is properly in
the catch tray and drop the front guard down (follow
place to ensure a watertight fitting.
the procedure described under CHANGING THE TUBES).
Unscrew one cap by turning it anticlockwise. Remove
the starter from its housing by turning it anticlockwise,
then extracting it downwards. Repeat the same
operation with the other starter. Fit the new starters
following the above procedure in reverse order. Take
Reflectobakt ® is the registered trademark of PestWest Electronics
great care that the black sealing gasket ring located
Limited.
®
sleeve is a
on the starter cap is properly in place to ensure a
Manufacturer reserves the right to vary model specifications without
watertight fitting.
notice.
Reflectobakt® is the registered trademark of PestWest
Electronics Limited.
Manufacturer reserves the right to vary
model specifications without notice.
®
sleeves from the used tubes and fit them
® SLEEVE.
® sleeves are correctly placed, shielding
®
is positioned at an equal
® sleeve with the pairs
® showing alignment in