Before using your new USB port PIC programmer please read this
instruction manual to prevent any damage. Put it away in a safe
place for future references.
•
To avoid damaging your programmer, please ensure pins are
connected to the correct side.
•
Do not place the PIC-600 over metallic surfaces.
•
Do not place metallic objects over the programmer
DRIVER INSTALLATION IN WINDOWS XP
1.- Place the installation CD into the CD-ROM drive.
2.- Run the program "PIC-600 Install Windows 98_Me_2k_Xp"
Follow the instructions.
3.- Use a USB cable type B (USB-450) to connect the programmer to
computer.
4.- The computer will detect the new hardware, the Found New
Hardware Wizard runs.
5.- Select No, not this time and click Next to continue.
6.- Now select Search for the best driver in these locations, click Next to
continue.
7.- Select Browse and locate the folder C: \ Program Files \
Steren pic-600 \ driver \ driver_98_Me_2k_Xp "
8.- The installation process begins. If a warning message pop up,
please click OK to continue.
9.- The completed installation window will appear shortly afterwards,
just click on Finish.
Do not place any PIC on the base while installing drivers, may
cause damages on it.
To install on Windows Vista you need to run the "PIC-600
Install Windows Vista" file, then follow the instructions.
IMPORTANT
Before to run the software, it is recommendable to connect the PIC
first, and then open the software, In the event of failure to do so
will have to recognize the programmer before starting to use it.
Connect the PIC-600 to an available USB port, open the PIC-600 file
installed in the program menu.
When the software recognize the programmer, next options will display
in the Basics tab:
Identify PIC in programmer
This option identify the placed PIC on the base or connected to ICSP
port. First, make sure to select the pins in the IC-Socket / ICSP box
dialog, and the family in PIC Family box dialog.
Select HEX-File as source
Open the file to be loaded into the PIC, it must have the .HEX format.
WARNING
OPERATION
Remove CP
Remove the code protection in some cases, it depends if the code
protection was installed in the program or while programming.
Erase PIC
Deletes the program or code in the connected PIC.
Blank check
Check if the PIC's memory is empty
Write HEX-File into PIC
Writes the program previously loaded with the Select HEX-File as
source option, into the connected PIC.
Compare PIC with HEX-File
Compares the content of the memory with the previously loaded
program.
Read from PIC into new HEX-File
Reads the Pic's memory and save into a new .HEX file, you must enter
a name and location for the file.
Target: Run
Use this option to switch the PIC to run mode after programming it into
the ICSP port. Be careful to insulate the ICSP port from the rest of the
circuit where the PIC is installed.
SPECIFICATIONS
5V
(through USB port)
Product design and specifications are subject to change without
previous notice.
This Steren product is warranted under normal usage against defects in workmanship and materials to the
original purchaser for one year from the date of purchase.
1.- This warranty card with all the required information, invoice or purchase ticket, product box or package,
and product, must be presented when warranty service is required.
2.- If the product stills on the warranty time, the company will repair it free of charge.
3.- The repairing time will not exceed 30 natural days, from the day the claim was received.
4.- Steren sell parts, components, consumables and accesories to costumer, as well as warranty service, at
any of the addresses mentioned later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God, mishandling, leaky batteries, failure to follow
enclosed instructions, improper repair by unauthorized personnel, improper safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket.
RETAILER INFORMATION
Name of the retailer
Address
Product
Brand
Part number
Serial number
Date of delivery
In case your product fails or have questions, please contact your nearest dealer. If you are in
Mexico, please give a call to our Call Center.
Call Center
01 800 500 9000
Product: USB port PIC programmer
Part number: PIC-600
Brand: Steren
WARRANTY
CONDITIONS