Revell Control GLOWEE 2.0 BEAST Manual De Instrucciones página 8

contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they
must be discharged or their capacity
must be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
The toy is only to be connected to Class
II equipment bearing the symbol:
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the transmitter and
1 HELICOPTER
1A Counter-rotating 2A ON/OFF switch
rotor blades
2B Thrust controller
1B Stabiliser
2C Antenna
1C Tail rotor
2D Left/right trim adjustment
1D LED
2E Controller for forwards and
1E Charge socket backwards flight as well as
rotation
1F ON/OFF switch
3 INSERTING BATTERIES (REMOTE CONTROL)
3A Unscrew and 3B Insert 6 x 1.5 V AA batteries
remove the and pay attention to the polarity,
cover as shown in the battery
compartment.
4 CHARGING THE HELICOPTER
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
1. Switch off the helicopter and the remote control.
2. Plug the USB charger into a USB hub or a USB port on a computer (4A).
3. Now insert the plug of the charger on the bottom side of the model (4B).
The charging process begins automatically.
14
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
Required battries for the
helicopter:
Rated output: DC 3.7 V / 0.93 Wh
Batteries: 1 x 3.7 V rechargeable
LiPo battery (integrated)
Capacity: 250 mAh
Charger:
Power supply: DC 5 V of USB port of
a PC or USB hub
Rated output: 4.2 V / up to 500 mA
Battery requirement for the
transmitter:
Power supply: DC 9 V
Batteries: 6 x 1.5 V "AA"
2 REMOTE CONTROL
2F ON/OFF button for LEDs
2G Charging cable compartment
2H Power LED
2I No function
3C Close the battery
cover and secure
with the screw.
4. The status LED on the USB charger lights up continuously when the charging process
starts. The charging process lasts approx. 50 minutes and must be continuously
monitored. The red LED on the charger goes out as soon as the charging process is
finished. Disconnect the battery from the charger and disconnect the charger from
the USB port once charging is complete.
The helicopter can fly for approx. 6-8 minutes after a charge time of
approx. 50 minutes.
Warning notice: The LiPo battery does not normally heat up while charging. If it
should become warm or even hot and/or changes to the surface begin to appear,
immediately discontinue the charging process!
You can also charge your helicopter with the remote control:
• Switch off the remote control and the helicopter.
• The charging cable plug is located on the side of the remote control (4D). First push
down the charging cable compartment and then carefully insert the cable into the
helicopter's charging socket (4E). The plug must be gently inserted into the charging
socket – DO NOT USE FORCE. If the plug is not correctly inserted into the charging
socket, the helicopter may become damaged and, under certain circumstances,
become an injury risk. Switch on the remote; the power LED blinks red. Slowly move
the thrust controller to maximum and then back to its starting position to activate the
remote control (2B); the power LED will begin to blink quickly. This process lasts for approx.
3 seconds. Now the LED continuously illuminates green.
• The charging process is complete as soon as the LED is illuminated red.
• After the charging process, switch the power switch to „OFF" and disconnect the
charge cable from the helicopter.
5 START PREPARATION
Set the remote control's ON/OFF switch to „ON" (5A). The power LED begins to blink.
Now set the helicopter's ON/OFF switch to the "ON" (5B). Place the helicopter on the
ground so that the tail points toward you (5C). Activate the remote control by slowly
moving the thrust controller to maximum and then back to its starting position; the
power LED will begin to blink quickly. This process lasts for approx. 3 seconds. The
helicopter is ready to start when the headlamp is permanently illuminated red.
6 TRIM ADJUSTMENT OF THE CONTROL
The correct trimming is a basic requirement for achieving fault-free flying from the
helicopter. Its adjustment is simple, but it requires some patience and a feel for it.
Please observe the following instructions precisely: Carefully move the thrust control
up and raise the helicopter approximately 0.5 to 1 metre in altitude.
6A If the helicopter quickly or slowly rotates clockwise by itself...
If the helicopter begins to automatically rotate clockwise, rotate the left/right trim
adjustment anti-clockwise until the helicopter no longer rotates on its own.
6B If the helicopter quickly or slowly rotates anti-clockwise by itself...
If the helicopter begins to automatically rotate anti-clockwise, rotate the left/right trim
adjustment clockwise until the helicopter no longer rotates on its own.
15