Dust/Chip Extraction; Operating Modes; Starting Operation - Würth HKS 65-E POWER Traducción Del Manual De Instrucciones De Servicio Original

Dust/Chip Extraction

 Before any work on the machine itself, pull the
mains plug.
Dusts from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dusts can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dusts, such as oak or beech dust, are considered as
carcinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be worked by specialists.
• As far as possible, use a dust extraction system suitable for
the material.
• Provide for good ventilation of the working place.
• It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
 Prevent dust accumulation at the workplace.
Dusts can easily ignite.

Operating Modes

 Before any work on the machine itself, pull the
mains plug.
Adjusting the Cutting Depth
(see figure B)
 Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
Loosen the clamping lever 24. For a smaller cutting depth,
pull the saw away from the base plate 13; for a larger cutting
depth, push the saw toward the base plate 13. Adjust the
desired cutting depth at the cutting-depth scale. Tighten the
clamping lever 24 again.
If the cutting depth cannot be fully adjusted after loosening
clamping lever 24, pull clamping lever 24 away from the saw
and swivel it downward. Release the clamping lever 24
again. Repeat this procedure until the requested cutting depth
can be adjusted.
If the cutting depth cannot be sufficiently locked after tighten-
ing clamping lever 24, pull clamping lever 24 away from the
saw and swivel it upward. Release the clamping lever 24
again. Repeat this procedure until the cutting depth is locked.
Adjusting the Cutting Angle
It is best to place the machine on the face side of the blade
guard 16.
Loosen clamping lever 8 and wing bolt 26. Tilt the saw side-
ward. Set the requested angle at the scale 6. Tighten clamp-
ing lever 8 and wing bolt 26 again.
Note: For bevel cuts, the cutting depth is smaller than the set-
ting indicated on the cutting-depth scale 25.
Cutting Marks
The 0° cutting mark (9) indicates the position of the saw
blade for straight cuts. The 45° cutting mark (10) indicates
the position of the saw blade for 45° cuts without using the
guide rail.

Starting Operation

 Observe correct mains voltage! The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Power tools marked with 230 V can also be
operated with 220 V.
Switching On and Off
To start the machine, first push the lock-off button for the
On/Off switch 2 and then press the On/Off switch 1 and
keep it pressed.
To switch off the machine, release the On/Off switch 1.
Note: For safety reasons, the On/Off switch 1 cannot be
locked; it must remain pressed during the entire operation.
To save energy, only switch the power tool on when using it.
Reduced starting current
The electronic reduced starting current limits the power con-
sumption when switching the tool on and enables operation
from a 13 ampere fuse.
Constant Electronic Control
Constant electronic control holds the speed constant at no-
load and under load, and ensures uniform working perfor-
mance.
Temperature Dependent Overload Pro-
tection
In case of overload, the machine switches off until the optimal
operating-temperature range is reached again. Release the
On/Off switch 1 and switch the machine on again to continue
working.
Speed preselection
The required speed can be preselected with the thumbwheel
3 (also while running).
The required speed depends on the saw blade being used
and on the material being worked.
20