RCBS ULTRASONIC CASE CLEANER 2 Instrucciones De Producto página 9

DISPLAY
1. Digital Timer Display - Displays the set run time.
2. Water Temperature Indicator
water temperature is 0-30% of the set temperature. Solid orange light
temperature is 30-60% of the set temperature. Solid red light
60-90% of the set temperature. Flashing red light
set temperature. All solid lights indicate that the water temperature is at the set temperature (90-100%).
3. Set Temperature Display - Display will show one of the 5 pre-set temperatures: 40°C/104°F, 45°C/113°F,
50°C/122°F, 55°C/131°F or 60°C/140°F.
4. Set Temperature Units Indicator - Indicates if temperature is either ºC or °F.
5. Solution Timer – Counts down to show remaining solution usage (Hour:Min).
6. Solution Set Indicator (
be reset. When
Cleaner is in operation.
7. Degas Status (
8. Heater Status (
is turned off.
9. Normal Cleaning Status (
10. Working Status - Indicator Light
Green - Ready: Green light indicates normal working status, ready to use.
Red - Overheat (R): Red light indicates overheat protection. 20 minutes or more time required for the light
to change from red to green. When light is green normal operation may resume.
KEYPAD
11. Heater Button — Heater On/Off Button. Pressing Heater button
is turned on. To cancel heating, press Heater button again and
turned off. When water reaches the set temperature the heater will turn off automatically.
b
12. Function Button - Functions (Degas/Normal). Depressing function button
indicating degassing function is desired. Depressing function button again
normal ultrasonic cleaning. Pressing On/Off button will begin cleaning. If unit is in degassing mode,
will flash for 2 minutes while unit is degassing. After 2 minutes has elapsed,
normal ultrasonic cleaning has begun and degassing has stopped. If more degassing is required depress
function button and
13. On/Off Button - On/off switch. When unit is plugged in and the unit is powered on the LED will
display, the default 05:00 minutes run time and the unit is ready to operate in the normal ultrasonic cleaning
mode for 5 minutes. Press the On/Off button once to initiate cleaning. The cleaning will stop when the
timer counts down to 00:00. If the unit needs to be Stopped, before the timer runs out, press the On/Off
button to turn off ultrasonic cleaning.
14. Button - Decreasing Button.
• When Time is used, each pressing reduces the timer by 1 minute.
• When Temp is used, each pressing reduces the set temperature down to the next level.
• When h/min is used, each pressing reduces the solution set time by 20 minutes.
15. h/min - Solution Timer Set Button. Each time
maximum time that can be set is 9 hr 60 min. When
button will reset timer.
16. Temp Button - Temperature set button. 5 pre-set temperatures can be selected. Press Temp button
to select the temperature in the following sequence: 40°C/104°F, 45°C/113°F, 50°C/122°F, 55°C/131°F or
60°C/140°F.
17. Time Button - Timer quick set button. Press Time button, LED will display run time. When time
button is depressed, time will increase by 5 minutes up to a maximum run time of 30 minutes.
NOTE: There is a overheat safety feature built into the RCBS Ultrasonic Cleaner, which will automatically shut
) - When
is displayed, solution timer is set and timer will begin counting down when Ultrasonic
) - When is displayed, unit is in degassing mode.
) – When is illuminated heater is turned on. If
) – When
will illuminate indicating degassing is underway.
- Solid green light
indicates that the water temperature is close to the
is flashing solution needs to be changed and timer needs to
is illuminated, normal cleaning is underway.
is depressed; the timer is increased by 20 min. The
flashes solution needs to be changed. Depressing
6
indicates that the water
indicates that the water temperature is
is not illuminated, the heater
will flash indicating heater
will dim, indicating heater has been
will illuminate indicating
will illuminate, indicating
indicates that the
will illuminate,