GE ATM06 Manual Del Propietario Y Instrucciones De Instalación página 5

Controls
Features and appearance will vary.
Air Conditioner Controls
1. Digital Display
When the timer is not in use, the operation mode and the set
temperature will be displayed. Time will be displayed under the
timer setting.
2. + and - Button
decrease the Set Temperature or Timer. Temperature range: 61°F
to about 88°F or 16°F to about 31°C.
3. Power Button
Turn the air conditioner on and off.
4. Mode Button
Press the mode button to cycle through the various modes. Cool,
Dry, Fan, and Auto.
Cool Mode: The cooling function allows the air conditioner to cool
the room and reduces the air humidity at the same time. Press
the Mode button to activate the cooling function. To optimize the
function of the air conditioner, adjust the temperature and the
speed by pressing the button indicated.
Dry Mode: This function reduces the humidity of the air to make
the room more confortable. Press the Mode button to set the Dry
mode. An automatic function of alternating cooling cycles and then
the air fan is acitvated.
Fan Mode: This function works only when the air conditioner is
ventilated. Press the Mode button to set the FAN mode. While
pressing the Fan Speed button, the speed changes in the following
sequence: High, Medium, and Low, in Fan mode. The remote
control also stores the speed that was set in the previous mode of
operation.
Auto Mode: In Auto mode, the unit automatically chooses the fan
speed and the mode of operation (Cool, Dry, or Fan). In this mode,
the fan speed and the temperature are set automatically according
to the room temperature (tested by the temperature sensor, which
is incorporated in the indoor unit.
5. Timer Button
Timer.
49-5000421 Rev. 0
1
8
9 7
6 5 4 3
Timer Off: the timed stop is programmed by pressing Timer Button.
Set the rest time by pressing the + or - buttons until the rest time
displayed is to your liking, then press the Timer button again.
Timer On: When the unit is off, press the Timer button, set the
temperature by pressing the + or - button. Press the Timer button
a second time, set the rest time by pressing the + or - button.
Press Timer button a third time, confirm the setting, then will
automatically switch on and will show the display.
NOTE: It can be set to automatically turn off or on in 0.5-24 hour
increments. Each press of the + or - buttons will increase or
decrease the timer. The timer can be set on 0.5 hours increments
below 10 hours and 1 hour increments for 10 hours or above.
The Set light will turn on while setting.
To cancel the set function, press the Timer button again.
6. Eco Button
When the unit is in ECO mode, the light will turn on. In ECO
mode, the unit will turn off once the room is cooled to the user-set
temperature. The unit will turn back on when the room temperature
rises above the user-set temperature. Before the compressor
starts, the fan motor will run for a while, then it will stop for a while,
and will repeat to provide a much more comfortable feeling and
save energy.
7. Sleep Button
Press the SLEEP button, all of the display lights will turn off after
a while, but the Sleep light is always on. In SLEEP mode, the air
conditioner will automatically adjust the temperature and fan speed
to make the room more comfortable during the night. The set
temperature will automatically raise every 30-60 minutes, and at
most change six times until the set temperature is 81 or 82.
8. Fan Speed Button
Press the FAN SPEED button to choose the fan speed options.
You can choose Hi, Med, Lo or auto speed in COOL mode or
choose Hi, Med, Lo in FAN mode.
9. Filter Button
hen the Filter Check light is off, it is not necessary to press the
Filter Check button. When the Filter Check light is on, you can
turn off the light by pressing the Filter Check button. After the fan
motor works for 500 total hours, the Filter Check light will turn on to
remind the user to clean the filter.
2
5