General Cleaning - Electrolux BEAM Alliance Solaire Manual

ASSEMBLY & OPERATING INSTRUCTIONS FOR THE POWERBRUSH
When using the powerbrush, the basic precautions outlined under "IMPORTANT SAFETY
INSTRUCTIONS" should always be followed.
1. Push the wand into the powerbrush socket until it locks in place. The wand
socket is designed with a positive stop. Therefore, the wand will not jam in the
wand socket. Insert hose end into the powerbrush wand on the assembled
powerbrush until is locks in place. (figure 3)
2. Make sure the hose handle button is OFF. Note: The handle is in the OFF
position when the indicator in the (
3. Insert the hose into the wall inlet valve (faceplate), and plug the cord into the
electrical outlet. (figure 4)
4. Lower the wand from the upright position.
5. To turn the central vacuum ON, press the (
6. To turn on the powerbrush, press the powerbrush button (
turn it on.
7. To turn off the powerbrush, press the symbol Powerbrush (
button. The indicator in the icon will turn off.
8. Disconnect the handle from the wand by pushing the button on the
wand that is closest to the handle, and pulling the handle out of the
wand socket.
9. Variable speed allows you to vary the suction power. Press ( + / - )indicator button. An
indicator in the handle will show bars and the different speed levels.
10. Release the wand from the powerhead by depressing the foot pedal and pulling the wand out
of the powerbrush socket.
Helpful Hint: To prevent possible damage to the Powerbrush, do not pick up hard or sharp
objects. Articles of clothing, towels, loose carpet edges, etc., should also be avoided. If an article
does become entangled in the brush roller, switch off the Powerbrush. Disconnect the hose
cord from electrical outlet and the hose from the faceplate and then remove the object carefully
without using excessive force.
WARNING: Always switch off the Powerbrush and disconnect plug from wall electrical
outlet and disconnect hose before servicing the Powerbrush.
1. The Powerbrush can be wiped with a cloth dampened with warm water and a mild detergent.
2. Do not use abrasive substances or any solvents.
Phoenix :: CUI1 & 2G
Power Nozzle Button
) button is OFF.
Power Button
(Phoenix & 2G)
Status OK
Left Scroll 2G-to-Unit Connection Power ON/Power Level
Performance Level
Right Scroll Time
Enter Error Code Bucket Level
Call for Service
Phoenix :: CUI1 & 2G
Motor Running
Attention Needed
) button.
Power Button
(Phoenix & 2G)
Status OK
Status OK
Phoenix :: CUI1 & 2G
Power Level Button
Left Scroll 2G-to-Unit Connection
(2G)
Power Button
(Phoenix & 2G)
Status OK
Right Scroll Time
Left Scroll 2G-to-Unit Connection
Phoenix :: CUI1 & 2G
Enter Error Code
Power Button
Call for Service
(Phoenix & 2G)
Right Scroll Time
Status OK
Attention Needed
Left Scroll 2G-to-Unit Connection
Enter Error Code
Status OK
Call for Service
Power Level Button
(2G)
Right Scroll Time
Attention Needed
Status OK
Enter Error Code
Power Level Button Call for Service
(2G)
Attention Needed
Status OK
Power Level Button
(2G)

GENERAL CLEANING

(2G)
(2G)
Power Nozzle Button
(2G)
Power Nozzle Button
Screensaver
Power ON/Power Level
(2G)
) to
(2G)
Performance Level
Power ON/Power Level
(2G)
Power Nozzle Button
(2G) )
Performance Level
Bucket Level
Motor Running
Power ON/Power Level
(2G)
Bucket Level
Performance Level
Screensaver
Motor Running
Figure 4.
Bucket Level
Screensaver
Motor Running
Screensaver
Figure 3.
5